XinqiuGkt12 hy
XinqiuMobile h
XinqiuFixed hyWhen conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs,XinqiuHydraulic lifting platform automatic, guardrails or safety nets should be installed on the side facing the air,XinqiuSmall hydraulic platform lift truck, or safety belts or ropes should be used.
Convert to Simplified Chinese Convert to Traditional Chinese without converting the number of blank lines between paragraphs before and after:
Xinqiu.When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
.Remove and disassemble the lowering valve, and then reinstall it.
Hydraulic loading elevators must strictly carry out load-bearing operations in accordance with regulations. Otherwise, it may harm people and objects!
When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
Drain all the hydraulic oil in the oil tank,XinqiuHydraulic loading and unloading platform, open the oil tank, take out the oil suction filter, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
assets.Regularly check the connection of each part, and tighten it if there is any looseness
For homepage | add favorites | email | QQ: If you have any questions, please QQ us!
Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.
demand.Remove trailing spaces, remove first and last interfering characters, remove blank lines, remove non paragraph blank lines, punctuation correction: Leading space type: Number of spaces:
When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
Function: Convenient unloading strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip devices: This device is welded from steel plates and can effectively achieve anti slip function, which is reliable.
Xinqiu.The use of highlights is cost-effective. When aluminum alloy elevators were in the market their price was also a significant highlight. Because manufacturers make reasonable and moderate pricing decisions in their daily processes, it is well known that manufacturers generally consider manufacturing costs when pricing. and
High stability of manufacturing materials. Usually, manufacturers can choose a variety of manufacturing materials when producing fixed loading and unloading platforms, and each material brings different effects when used. For many manufacturers, in order to improve the stability of loading and unloading platforms during use, they attach great importance to the selection of manufacturing materials. Generally, materials with high stability will be used as much as possible, as such materials can achieve better results in application.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.