HuvdopFixed li
HuvdopLifting After working for 10000 hours, repair the mechanical and electrical systems of the elevator.
When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.
Huvdop.Everyone knows that many industries use hydraulic elevators, and when using them, it is necessary to ensure the stability of the machine. If the machine is unstable, it will have a significant impact during use. So, what details cannot be ignored during the use of hydraulic elevators?
The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!
.Using Help | Updating Logs | Original Software | Daily Software
Then, the lifting platform platform platform that carries the load needs to be balanced, and no deviation of one side is allowed. The lifting of goods does not allow people to stand on both sides of the platform, and the lifting of goods should try to maintain a stable and uniform speed.
Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
It can be seen that the hydraulic lifting platform needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
After 5000 hours of operation of the elevator, repair the mechanical and electrical systems.
Professional is king.High stability of manufacturing materials. Usually, manufacturers can choose a variety of manufacturing materials when producing fixed loading and unloading platforms, and each material brings different effects when used. For many manufacturers, in order to improve the stability of loading and unloading platforms during use, materials with high stability will be used as much as possible as such materials can achieve better results in application.
Using Help | Updating Logs | Original Software | Daily Software
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
Finance Department.Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Of course, it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength,HuvdopDual hydraulic lifting platform, especially the construction lift has relatively high requirements for production technology. Therefore, when making a purchase, it is important to consider the factory building and process of its production,HuvdopDouble layer hydraulic lifting platform, all of which are very important.
Huvdop.For project engineering if the selected construction elevator can ensure the safety of construction workers, of course, it can also improve the overall work efficiency of the construction. Therefore, there are many manufacturers and types of construction elevators on the market, and facing the mixed situation of good and bad,HuvdopMobile hydraulic platform, many customers have no choice when choosing. In fact, when choosing elevators, the first thing to pay attention to is their quality, so that they can choose suitable elevators. But now many customers have high requirements for craftsmanship when choosing elevators.
Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes, multiple limit switch protection, door and power outage protection, leakage protection, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.
Troubleshooting: When the elevator power light is turned on, press the up button, the motor rotates, but the lifting platform does not rise. This may be due to the reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.