TheofokHydraul
TheofokLight hThe lifting stage can achieve the lifting of a double-layer tabletop. It can also be pieced into a stepped, multi scenic, and multi-level staircase as needed, a large load-bearing capacity, smooth lifting simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.
Theofok.When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
Using Help | Updating Logs | Original Software | Daily Software
.Secondly for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.
We
Secondly, using oil cylinders and chain transmission, with very few moving components, so the maintenance workload is not very high. Moreover, this type of lifting cargo elevator has a very compact structure and uses fewer bearings, resulting in a longer service life.
Safety protection components, in order to ensure safety production, it is essential to install a lifting platform for proper protection. The main protective accessories include safety belts, guardrails, protective covers, platform stairs, etc.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
Safety and health.Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex,TheofokHydraulic automatic lifting platform, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves,TheofokPlatform lifting platform hydraulic, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits,TheofokLoading and unloading hydraulic platform, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.
Later, when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs, it should not be used again to avoid accidents, personnel and property losses.
Regularly check all wires and cables for damage, and promptly wrap and replace the damaged parts.
Sampling inspection.When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.
Therefore, when making a selection, I believe everyone has a certain understanding of elevator selection so that they can have a clear goal when choosing, and then choose the elevator that is suitable for customers.
Theofok.After working for 10000 hours, it is strictly prohibited to lift them.
The reduction gearbox the legs must be opened first. If the legs are not lifted, gearbox, external gear teeth, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.