Bolzano12 meteBolzano22 meter elevator,BolzanoPlant Lift,
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Bolzano.The anti-corrosion measures for the body of high-altitude work vehicles should pay attention to small scratches. The paint surface of high-altitude work vehicles often corrodes. In addition to common collisions, scratches, there can also be a peeling point, which will cause a small rust over time. Because most of these scars are small and easily overlooked. Therefore, regular inspections should be conducted on the engine hood and surrounding areas. Once discovered, it is necessary to promptly go to a professional beauty shop for processing.
Systems: explosion-proof electronic control system, remote control system and PIC system. Professional elevator manufacturers have stable, safe, reliable performance, and can achieve maintenance free. Their technical level has reached the domestic level and reached the advanced level of similar international products
.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.
Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.
Purpose The hydraulic lift is widely used in various industrial enterprises and production lines such as automobile, container, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting requirements of different operation heights and can be equipped with various table forms (such as ball, roller, turntable, steering, and with various ways (separate, linkage, it has the characteristics of stable and accurate lifting, frequent starting and large load capacity, Effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations easy.
The main categories of aluminum alloy elevators in the Chinese market are based on the structural form of aluminum alloy elevators. Aluminum alloy lifting platforms can be divided into the following types: single column aluminum alloy lifting platforms, which are light and small in equipment, flexible in movement, generally no more than 12 meters in height, and generally have a load capacity of less than 150 kilograms especially suitable for one person operation.
The appearance of hydraulic boarding bridges to customers, and the demand for boarding bridges is also increasing. However, there are not many manufacturers of corresponding boarding bridges. Many boarding bridge companies are leather bag companies, and they do not produce them themselves, resulting in high prices. What is important is that they do not have a good understanding of the technology of car booths, and there are often deviations when passing on the technical requirements of direct customers to the manufacturers. Therefore, customers who purchase boarding bridges can directly find professional manufacturers. When choosing a boarding bridge, the first thing to consider is the range of use, frequency of work, utilization, rated weight, and other factors of the product, and then the after-sales service capability. As long as it is a fixed boarding bridge with good product quality excellent performance, and complete equipment, it can be chosen at a reasonable price.
Statistics.2: Chemical rust removal mainly involves the use of acid to react with the metal components of the screw elevator to remove rust products from the rust surface of the push rod. This type of rust removal is mainly used for large mechanical screw elevators, and attention should be paid to protecting precision devices such as electronic instruments from acid corrosion during use.
What is the solution to the problem of surface rust on the spiral elevator? The deficiency is that sandpaper has a significant loss on the spiral elevator itself.
Reset the brake; Installation and maintenance section. The maintenance section is generally installed in the fourth section. Long term promotion of downgrading manufacturers, 20 year old brand, with price advantages and guaranteed quality!
Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.
average method.When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
A large logistics warehousing equipment service company directly operated by manufacturers with guaranteed prices and guaranteed services. Due to the fact that fixed elevators are mechanical equipment, the product quality and performance are good. Do not accept products from some manufacturers that do not meet the quality standards to avoid potential safety hazards during use.
Elevating platform price elevators and elevating platforms are used for large-scale high-altitude continuous operations such as airport terminals, aircraft repairs, stations, docks, shopping malls, sports venues, residential properties, factories and mining workshops. Some products have the function of active walking, allowing for fast and slow walking under different operating conditions. With just one person in the air, the machine can be operated to complete actions such as up and down, moving, retreat, and turning. When the machine is in a suspended state, the wheels are always in a braking state and can firmly brake on a 6 degree slope. The large diameter and ultra wide high-quality rubber wheels provide users with useful maintenance on the ground and increase the friction force during braking.
Bolzano.Gear pump worn, aged or damaged; The solution is to replace the gear pump. Professional elevator manufacturers have advanced technology, strict testing, more affordable prices,BolzanoCustomization of electric elevators, and more discounts. Welcome to consult
Outdoor elevators and factory cargo elevators are heavy lifting mechanical equipment. Outdoor elevators are used for transporting goods between floors of buildings, and are specialized hydraulic cargo elevator products. They are mainly used for transporting goods up and down between various working floors; Vertical garage and car lift between garage floors. The hydraulic system of the product is equipped with anti fall and overload protection devices, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point operation.
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.