Check the rollers, intermediate shafts,HaConstruction site small elevator,HaScissor lift, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
The normally closed valve and motor are energized simultaneously; The solution is correct wiring, and the motor often closes the valve and loses power when powered on.
Ha.Novice operators should pay attention to which equipment wears quickly when operating mobile elevators: Due to factors such as the processing and installation of high-altitude work platform equipment components such as mobile elevators, the equipment surface is rough, the area is small, and the load bearing is uneven, which can cause equipment wear. During the operation of high-altitude work platform equipment such as mobile elevators, the concave and convex parts on the surface of the parts are embedded and friction with each other, which will accelerate the wear and tear of the surface of the equipment parts. Therefore, with a fast wear rate.
Reset the brake; Installation and maintenance section. The maintenance section is generally installed in the fourth section. Long term promotion of downgrading manufacturers 20 year old brand, with price advantages and guaranteed quality!
.The elevator has a strong load-bearing capacity and is suitable for two people (who can carry a certain amount of weight tools and materials) to climb high at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
Hydraulic lifting platforms are widely used in factory maintenance, municipal construction, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no
What should I pay attention to when starting a new mobile elevator? High priced and various specifications of elevator manufacturers welcome scrap merchants,HaScissor fork mobile lifting platform, industrial companies, and power departments to visit and negotiate with the company!
The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
Superior quality.Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.
Single column aluminum alloy elevator: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has lifting balance, easy operation, and can enter general lobbies. It can enter and exit the elevator at will with low power consumption, no pollution, and does not harm the ground during work. It can be used for wall work and exploration work, and there are no dead corners during work. The single column aluminum alloy electric elevator, equipped with gantry cross frame accessories, is very suitable for maintenance work in cinemas, auditoriums, etc.
Nowadays, elevators are widely used and are involved in many industries. The spiral elevator is no exception and has a very good effect. But sometimes the surface of the spiral elevator will rust, which has a certain impact on work efficiency and needs to be removed. So what is the solution to the surface rust of the spiral elevator?
A type of elevator equipment consisting of a walking mechanism, hydraulic mechanism electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
recommend.Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.
What should I pay attention to when starting a new mobile elevator? High priced and various specifications of elevator manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!
According to different needs, different power modes can be selected such as three-phase AC power supply, DC power supply, and internal combustion power supply. With manual hydraulic equipment, lifting operations can be carried out in places with power outages or no power supply, and components can be added. When the platform length is insufficient, it can be extended to the required direction, and then the operating power can be increased. It is a must-have product of modern large-scale construction and equipment, and a necessity for high-altitude safety and civilized production.
Ha.Elevator cables play an important role in elevators, but do you know how to choose good cables? Below, the editor will summarize how to choose good elevator cables for everyone. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assurance
Elevator cables play an important role in elevators but do you know how to choose good cables? Below, the editor will summarize how to choose good elevator cables for everyone. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assurance
The hydraulic lifting platform mainly uses hydraulic oil pressure transmission to achieve the lifting function. Its shear fork mechanical structure provides stability for the lift. The wide working platform and high bearing capacity make the high-altitude operation range wide and suitable for multiple people to work simultaneously. It makes high-altitude operations efficient and guaranteed.