Agnel sur Seine16 meter lift truckRealize the transformation of product structure

Four column aluminum alloy elevator: the whole elevator is made of high-strength aluminum profiles. Due to the high strength of the profiles, the four mast structure is adopted,Agnel sur Seine10 meter electric elevator, which has excellent stability, flexible operation, large platform area and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. Minimize the deflection of the lifting platform.

Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, paying attention to driving habits can ensure that high-altitude work vehicles do not rust. Here are a few points for reference.

Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning.

.Curved arm elevator: a lifting device used for high-altitude operations, which can cross obstacles for high-altitude operations. When the platform is lifted to any position, it can operate while walking, with a compact structure and flexible turning. The width of its site can ensure that the equipment enters narrow passages and crowded working areas. The backup power device can operate the work platform to reset, and is a convenient transportation method that can be towed to any place.

This series of products has a load capacity of 0.1 to 0.8 tons, and can also be customized according to user requirements, with a load capacity of up to 10 tons.

When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.

Single column aluminum alloy elevator: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has lifting balance, easy operation, and can enter general lobbies. It can enter and exit the elevator at will with low power consumption, no pollution, and does not harm the ground during work. It can be used for wall work and exploration work, and there are no dead corners during work. The single column aluminum alloy electric elevator, equipped with gantry cross frame accessories, is very suitable for maintenance work in cinemas, auditoriums, etc.

Nowadays, small and medium-sized enterprises embrace the idea of good quality and discounted prices for their products.

Hydraulic lifting platforms are widely used in factory maintenance, municipal construction, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.

How much is it.Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no

The advantages and application fields of elevators and lifting platforms. The lifting mechanism is made of high-strength manganese steel giant tubes. Equipped with safety maintenance equipment to avoid overloading of elevators. Equipped with a safety maintenance valve to prevent hydraulic pipeline cracking. Equipped with emergency lowering equipment in case of power outage. This product is suitable for mobile high-altitude operations such as high-altitude equipment and maintenance in various industries.

Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning.

This series of products has a load capacity of 0.1 to 0.8 tons, and can also be customized according to user requirements, with a load capacity of up to 10 tons.

retailer.The current should exceed the rated current, and even cause the motor to stop on its own. If the shutdown time is slightly longer and the power supply is not cut off, the winding will not only overheat severely, but also burn out. When a star connected motor is mistakenly connected into a triangle,Agnel sur SeineElevator, or a motor with multiple coil groups connected in series into a branch is mistakenly connected into two parallel branches,Agnel sur SeineFactory automatic elevator, it will cause the winding and iron core to overheat, and in severe cases, the winding will be burned out.

It is good not to cover the car with clothes for high-altitude work vehicles. If the vehicle is parked outside in windy and rainy weather, the clothes will repeatedly slap the car paint, especially if the car is blowing sand on the clothes, it will draw many small scratches on the clothes, because over time, it will lead to black paint. In addition, when the wind does not directly spray powder or clean the mechanism on the sand, it should be washed with water and prevent the high-altitude work vehicle vacuum cleaner from scratching the sand particles on the paint surface.

The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.

Agnel sur Seine.The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.

The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, blow the valve core clean with compressed air but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.

Remove and disassemble the lowering valve, and then reinstall it.