PotsdamMobile lifting hydraulic boarding bridgeCost-effectiveness of the industry

Chinese manufacturer of boarding bridges, dedicated to mobile lifting (sh ē Ten series of hydraulic lifting platform products, including platform, self-propelled aerial work platform, fixed lifting platform, TTW guide type cargo lift, aluminum alloy (melting point 660 ℃) lifting platform, jacketed lifting platform, folding arm lifting platform, car mounted lifting platform, disabled lifting platform, lifting stage, boarding bridge, etc, All properties owned by the company

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

Potsdam.Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials, which will result in unexpected loss of performance in the application process.

It mainly includes the strong wind load acting on the structure, the lateral force caused by the inclined operation of the fixed hydraulic boarding bridge when lifting the channel,PotsdamMobile lifting hydraulic boarding bridge, the horizontal load on the structure caused by suspended objects under wind load, the fixed hydraulic boarding bridge, as well as temperature load, technical load,PotsdamProfessional boarding bridge, and ice and snow load. The special load of fixed hydraulic boarding bridge refers to the large load that may be encountered by the lifting equipment during non operational conditions, or the occasional unfavorable load encountered during operational conditions. This load is encountered in both hydraulic lifting channels and fixed hydraulic climbing bridge lifting channels.

.It mainly includes the strong wind load acting on the structure, the lateral force caused by the inclined operation of the fixed hydraulic boarding bridge when lifting the channel, the horizontal load on the structure caused by suspended objects under wind load, the fixed hydraulic boarding bridge as well as temperature load, technical load, and ice and snow load. The special load of fixed hydraulic boarding bridge refers to the large load that may be encountered by the lifting equipment during non operational conditions, or the occasional unfavorable load encountered during operational conditions. This load is encountered in both hydraulic lifting channels and fixed hydraulic climbing bridge lifting channels.

Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T, large static load: 6T, large width: 2M, large length: 4M. There are many classifications generally divided into mobile boarding bridges and fixed boarding bridges. General: Solid tires with a length of 11M and a width of 1M. The Ramp loading and unloading platform is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.

The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, but also prevents the accumulation of grease, dirt, rainwater, and ice and snow. This equipment is particularly suitable for explosion-proof and flammable places, with manual hydraulic power, without generating sparks and no worries. The power can be configured as: manual hand pump power. Electric power. Ensure that the oil cylinder is processed by iron cutting and rolling. Several maintenance and upkeep items for the fixed boarding bridge: each rotating shaft pin should be maintained regularly to reduce wear and enhance flexibility in use; The use of hydraulic oil should follow the specified model, usually 46 # or 68 #, which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, and the market should clean the dust, sand, oil, iron blocks, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding, or looseness and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, which can meet the installation and use of most loading and unloading platforms.

Promise and keep promise.The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition with good sealing performance and long service life.

The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions, tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.

　　2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.

Discount.The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, but also prevents the accumulation of grease, dirt, rainwater, and ice and snow. This equipment is particularly suitable for explosion-proof and flammable places, with manual hydraulic power,PotsdamContainer loading bridge, without generating sparks and no worries. The power can be configured as: manual hand pump power. Electric power. Ensure that the oil cylinder is processed by iron cutting and rolling. Several maintenance and upkeep items for the fixed boarding bridge: each rotating shaft pin should be maintained regularly to reduce wear and enhance flexibility in use; The use of hydraulic oil should follow the specified model, usually 46 # or 68 #, which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, and the market should clean the dust, sand, oil iron blocks, etc. on them. During maintenance, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding, or looseness, and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, the boarding bridge manufacturer - editor will provide a detailed introduction (xiá ng xì)

Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, which will result in unexpected loss of performance in the application process.

It is understood that the mobile liquid boarding bridge is a specialized auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. The mobile liquid loading and unloading bridge is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. By using artificial hydraulic power, the height adjustment of the boarding bridge can be achieved without the need for external power supply. The adjustable length of the cable chain is used to hook the vehicle, ensuring that the boarding bridge always fits tightly with the vehicle even in case of displacement. The mobile wheel is made of solid tires, which do not require inflation. It is sturdy and durable, combined with brake pads to ensure safe operation.

Potsdam.The equipped brake pads can effectively prevent the shifting of the boarding bridge during truck loading and unloading.

The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.

It is understood that the mobile liquid boarding bridge is a specialized auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. The mobile liquid loading and unloading bridge is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. By using artificial hydraulic power, the height adjustment of the boarding bridge can be achieved without the need for external power supply. The adjustable length of the cable chain is used to hook the vehicle, ensuring that the boarding bridge always fits tightly with the vehicle even in case of displacement. The mobile wheel is made of solid tires, which do not require inflation. It is sturdy and durable, combined with brake pads to ensure safe operation.