AnaheimFreight
AnaheimHydraulThe elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.
Anaheim.There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature, which is reflected in the lowering of the position on the table.
Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.
.The electromagnetic coil of the electromagnetic directional valve is not firmly fixed,AnaheimFixed electric hydraulic lifting platform, and frequent separation and suction can also produce high noise.
Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and are mainly used in factories, government agencies commercial stores, and the construction and decoration industry.
Safety advantages: Hydraulic elevators are equipped with the safety devices of traditional traction elevators: overflow valve: it can prevent system pressure from being too high when going up; Emergency manual valve: In case of power failure, it can cause the car to emergency descend to the nearest floor position, causing the car to emergency descend to the nearest floor position, and causing the emergency in the car to descend to the nearest floor position; Pipeline rupture valve: When the hydraulic system's pipeline ruptures and the car stalls and descends, it can automatically cut off the oil circuit and stop descending; Oil temperature protection of oil tanks: When the oil temperature of the oil tank exceeds the standard setting value, the oil temperature protection device sends a signal to stop the use of the elevator and wait for the oil temperature to decrease before starting the elevator. Long term promotion of downgrading manufacturers, 20 year old brand, with price advantages and guaranteed quality!
Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.
target.Lines of various safety equipment
The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.
Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.
There is noise inside the hydraulic cylinder. When replacing the hydraulic oil,AnaheimScissor fork hydraulic lifting platform, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
Quality risk.A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve hydraulic control one-way valve, and balance valve,AnaheimMobile hydraulic lifting platform, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Oil cylinder leaks. Long term use causes wear on the sealing ring in the oil cylinder and excessive oil leakage in the cylinder wall gap, resulting in the natural descent of the hydraulic cargo elevator. The sealing components need to be replaced immediately.
Remember not to overload, overload is the root cause of many faults.
Anaheim.The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
Lines of various safety equipment
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.