ryan 6 degreesThen, the lifting platform platform platform that carries the load needs to be balanced, and no deviation of one side is allowed. The lifting of goods does not allow people to stand on both sides of the platform, and the lifting of goods should try to maintain a stable and uniform speed.
Using Help | Updating Logs | Original Software | Daily Software
ryan .The characteristics of hydraulic lifting platforms are obvious, such as their relatively light overall weight and good maneuverability, allowing even a single person to operate,ryan Electric hydraulic unloading platform, making them relatively suitable. The mast columns of its system are equipped with guide wheels, attention should also be paid to the structure of the hydraulic lifting platform to ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
Copyright © 2006-2022 Yan-wei.Net.All Rights Reserved.
.The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
Secondly, the maintenance of the guide rail type hydraulic lifting platform is also very simple, using oil cylinders and chain transmission, so the maintenance workload is not very high. Moreover, this type of lifting cargo elevator has a very compact structure and uses fewer bearings, resulting in a longer service life.
For project engineering, if the selected construction elevator can ensure the safety of construction workers, of course, it can also improve the overall work efficiency of the construction. Therefore, there are many manufacturers and types of construction elevators on the market, and facing the mixed situation of good and bad, many customers have no choice when choosing. In fact, when choosing elevators, the first thing to pay attention to is their quality, so that they can choose suitable elevators. But now many customers have high requirements for craftsmanship when choosing elevators.
The drive motor can stop the movement of the rack on the pillar.
When a hydraulic lifting platform malfunctions, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.
Quotation sheet.Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
When the motor overheats it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.
Shafts must have split pins and be sufficient.
recommend.Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.
The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
The hook of the seat belt should not be hung on unstable or moving objects.
ryan .Firstly an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore,ryan Electric hydraulic platform, a power source is used as the lifting power source,ryan Unloading hydraulic platform, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.