FlorenceFully electric hydraulic lifting platformProduction steps and inspection requirements

The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety,FlorenceHydraulic lifting platform for automobiles, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings, pipelines, pressure gauges,FlorenceSmall mobile hydraulic lifting platform, and steel structure bases; Safety devices: safety valves, limit limits,FlorenceHydraulic experimental platform for teaching, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.

Replace with

Florence.The electric lifting platform needs to work under load according to the regulations on the nameplate during use, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.

Shafts must have split pins and be sufficient.

Later, when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs, it should not be used again to avoid accidents personnel and property losses.

Regardless of the type of lifting platform used, but also has varying degrees of impact on the safety during use people are more concerned about the stability during use. Because the stability not only affects the actual use effect, it is necessary to pay appropriate attention. The same applies when using fixed loading and unloading platforms, but many times the stability of this type of platform can be trusted. The reason for saying this is because the manufacturer has taken this issue into account during production and manufacturing, and the following aspects are taken to avoid this situation.

When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case there may be short lines or damaged components. Using a table for inspection is relatively better.

The above detailed introduction, I believe everyone has a certain understanding of elevator selection, so that they can have a clear goal when choosing, and then choose the elevator that is suitable for customers.

Manufacturing cost.For customers to use and operate the lifting platform for a long time, the editor briefly introduces how to maintain and repair the lifting platform: First of all, normal maintenance is mainly focused on prevention, especially if any damage or malfunction is detected and corrected or repaired in a timely manner. Careful inspection and maintenance at this time can save costs and avoid larger problems, resulting in costly repairs.

Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.

When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.

The following is a brief description of the precautions for using high-altitude work platforms: high-altitude workers must hold a health certificate. Individuals with mental illness, hypertension, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.

Inspection standard.There are many types of materials that manufacturers can use in the manufacturing process of the same lifting equipment, but the lifting equipment manufactured from different materials will also be different. The material used by manufacturers in the manufacturing process of aluminum alloy elevators is aluminum alloy with very high strength. It should be noted that this type of material itself has many advantages, so the sales of the elevator equipment made in the market are also considerable. Of course, for many people, the reason why they choose this type of lifting equipment is also closely related to its marketing highlights.

When using a hydraulic lifting platform, there are many details that cannot be ignored. It mainly uses an external power supply, personnel need to master its operating knowledge, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?

If the elevator malfunctions, non electrical professionals are not allowed to disassemble and assemble electrical appliances at will to prevent accidental connection or electric shock!

Florence.Shafts must have split pins and be sufficient.

Website homepage

two