HaCan hydrauli
HaHydraulic liit is necessary to have production technology
For the safety performance of high-altitude work platforms, scientific processes,HaScissor fork hydraulic lifting platform, and strict management to ensure production. When in use, people, the environment and machines are the three major links of high-altitude operations, and safety is the basic condition to ensure the smooth progress of high-altitude operations. In the following text, Jiuyi briefly describes the precautions for using high-altitude operation platforms: high-altitude operators must hold a health certificate. Individuals suffering from intentional, high-pressure, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.
The daily maintenance of guide rail type cargo elevators should ensure that the transmission position where the grease nipple is located needs to be lubricated twice a month. For areas where grease cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
Ha.Whether it is a large machinery with complex structure or a small to medium-sized equipment with simple structure, the maintenance work scope is mainly focused on cleaning, adjustment, fastening, and corrosion prevention, commonly referred to as" Cross homework”.
The correct construction inspection of the airport is to first inspect the foundation to see if there is any water accumulation and to see if the grounding system meets the requirements. We also need to see how the structural bolts of this frame are tightened, and whether there are any cracks in the welds. We need to set them according to the instructions. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, there are also many safety equipment for elevators.
.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.
Before installing the elevator bearings, do not open the packaging too early. This can easily lead to premature bearing contamination, which can lead to premature bearing damage. Additionally, ensure that the installation environment is clean and do not bring iron filings, dust, Prolonged use can also affect the running in between bearings, leading to a decrease in the lifespan of the elevator.
Maintain a smooth access road for external construction elevators and sufficient parking space for equipment. When using a crane for auxiliary installation, full consideration should be given to whether the on-site environment meets the operating conditions of the crane.
There are foreign objects inside the oil delivery pipe of the hydraulic lifting platform, which can cause uneven force distribution during the delivery of hydraulic oil, resulting in uneven surface conditions. It is recommended to carefully check whether the delivery pipe is smooth.
The question of how to extend the service life of hydraulic lifting platforms will be briefly discussed here. Many people may not be familiar with this type of equipment especially those who do not know which factories are producing such equipment. It is recommended that friends can search online because many sellers and producers of this type of equipment now have their own official websites, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, which is suitable for working at low temperatures.
discount.Installing bearings for elevators may seem simple, but it is also important to pay attention to some details, such as: it is actually difficult to thrust bearings into the shaft pins when excessively installing them. However, sometimes, some people may think of using a hammer to hammer the bearings for convenience, and use brute force during installation. In fact, directly hitting the bearings with a hammer can cause significant damage to the bearings, which is the main reason for bearing damage and reducing the service life of the bearings. So when installing bearings we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated. For a long time, the manufacturer of scissors lift has never changed hands to avoid price difference, and the price is 20% higher than the market value! More than one ton is more expensive!
Test method.The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%. Specializing in product and renewable resource business, including: scissor lift manufacturers
When using the hydraulic lifting platform, it is also necessary to check for overheating, as this equipment is equipped with a motor. If the motor is overheated, it may cause damage to the motor. However, replacing a motor is relatively expensive. Therefore, during driving or trial operation, if the motor is found to be overheated, it should be stopped immediately, and then the fault that caused the motor to overheat should be checked and eliminated, Only then can the machine continue to be used.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated. For a long time, the manufacturer of scissors lift has never changed hands to avoid price difference, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter,Ha12 meter hydraulic lifting platform, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.
The main structure and purpose of a guide rail elevator: The mechanical part of a guide rail elevator mainly includes three parts: a lifting device, a track device, and a belt changing device. The lifting device is mainly used to suspend the person being lifted, which is the core part of the entire mechanism. The track device is mainly used to provide movement trajectory, making operation more smooth. The belt changing device is used to switch tracks when the elevator is about to pass through a door. The internal structure of the lifting device is mainly composed of gear mechanism, bracket,HaHydraulic small lifting platform, guide mechanism, lifting arm, upper and lower shells, etc. The gear mechanism mainly includes large and small gears, winding pulleys, central shafts, and safety devices composed of stop buckles and torsion springs.
No matter what problem occurs, if encountering an unsolvable problem with a hydraulic lifting platform, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.