toray 10 ton mobile boarding bridgeWhat practical problems have been solved

Firstly,toray Container boarding bridge, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition, whether the movement and working speed are stable, and whether the display is normal

The lip plate is connected to the platform using a full length shaft, strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable. Various legitimate qualifications for boarding bridge factories. Welcome to inquire by phone and sincerely invite cooperation!

Function: Convenient unloading, strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable.

.A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.

The fixed hydraulic boarding bridge has three fundamental elements: purification, overheating,toray Simple boarding bridge, and air intake. There is a close internal connection between these three unfavorable factors, and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.

　　2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

Precautions for safe use of fixed hydraulic boarding bridges When operating the machine, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, and do not overload or deviate. The rated load of the fixed hydraulic boarding bridge specified by the manufacturer is the total weight of the loaded goods and forklifts, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, which greatly improves the loading and unloading power (referring to the amount of work done by objects in a unit of time), and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework

The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixed

Adopting imported integrated modular hydraulic station, with good sealing performance and long service life.

Direct material.The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, but also prevents the accumulation of grease, dirt, rainwater, with manual hydraulic power, usually 46 # or 68 #, which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, sand, oil iron blocks, etc. on them. During maintenance, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding, or looseness, and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, the boarding bridge manufacturer - editor will provide a detailed introduction (xiá ng xì)

The lip plate is connected to the platform using a full length shaft which has high strength and good reliability.

Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.

Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.

Administration.The fixed hydraulic boarding bridge has three fundamental elements: purification, overheating, and air intake. There is a close internal connection between these three unfavorable factors, and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.

Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor improve work efficiency, and obtain greater economic benefits.

Firstly, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal whether the switch and governor are in good condition, and whether the display is normal

toray .Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T, large static load: 6T, large width: 2M,toray Mobile Yard Ramps , large length: 4M. There are many classifications, generally divided into mobile boarding bridges and fixed boarding bridges. General: Solid tires with a length of 11M and a width of 1M. The Ramp loading and unloading platform is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.

There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.

A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.