StavaraPlatform hydraulic lifting platformCauses of quality

StavaraHydraulic lifting platform,

Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be 40-50 millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part tighten the pipe joint.

Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.

Stavara.Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course the hydraulic electrical system does not need to be adjusted in this situation.

When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.

.When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.

Leading spaces in blank lines Full width: Font size: Replace: Replace

Hydraulic loading elevators must strictly carry out load-bearing operations in accordance with regulations. Otherwise, it may harm people and objects!

Then, the lifting platform platform platform that carries the load needs to be balanced, and no deviation of one side is allowed. The lifting of goods does not allow people to stand on both sides of the platform, and the lifting of goods should try to maintain a stable and uniform speed.

The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.

Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.

Service first.Troubleshooting: When the elevator power light is turned on, press the up button, the motor rotates, but the lifting platform does not rise. This may be due to the reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.

When we use hydraulic elevators in our daily lives, we need to regularly inspect and maintain them. This not only extends the lifespan of the hydraulic elevators, but also allows them to exert greater power in their work. For example, the transmission part requires sufficient oil, and consuming components must be regularly inspected, maintained, or replaced. Mechanical bolts, especially those that frequently vibrate, such as rotating supports and lifting arm connecting bolts, must be tightened or replaced immediately when they become loose. Next, the editor will introduce how hydraulic elevators should be maintained.

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.

The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, with manual and automatic doors. Generally,StavaraSmall mobile hydraulic lifting platform, open platforms do not have doors. The electrical part is composed of power,StavaraHydraulic household lifting platform, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, rupture valves, emergency switches, and electrical short circuit protection.

quality standard.Regularly check all wires and cables for damage, and promptly wrap and replace the damaged parts.

When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.

Regularly check the connection of each part, and tighten it if there is any looseness

Stavara.High stability of manufacturing materials. Usually, manufacturers can choose a variety of manufacturing materials when producing fixed loading and unloading platforms and each material brings different effects when used. For many manufacturers, in order to improve the stability of loading and unloading platforms during use, they attach great importance to the selection of manufacturing materials. Generally materials with high stability will be used as much as possible, as such materials can achieve better results in application.

High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.

Convert to Simplified Chinese Convert to Traditional Chinese without converting the number of blank lines between paragraphs before and after: