LouisvilleHydr
Louisville10 mLouisvilleElectric hydraulic lifting platform,
Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.
The hydraulic pump produces noise. When the hydraulic elevator rises the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.
Louisville.Many operating factories often require the use of hydraulic cargo elevators, which can be lifted and lowered, making it very convenient to use. Many people do not know the knowledge of hydraulic cargo elevator lifting and adjustment. If they understand this knowledge, it will be helpful for future maintenance. The power unit of the fixed chain elevator for hydraulic lifting of cargo elevators drives the hydraulic oil to generate pressure, causing the oil cylinder to move back and forth to drive the lifting platform, thus achieving the adjustment of lifting speed. The power unit adjustment, whether it is a scissor type lifting platform or a track type lifting platform, is composed of the power unit and the oil cylinder. The power unit is manufactured with four outlet holes, which can be adjusted in size to increase or decrease the hydraulic oil flow rate of the oil cylinder, Adjustable motor speed or electro-hydraulic proportional valve to adjust hydraulic oil flow rate; The longer the oil pipe and hydraulic oil pipe, the longer the rise time. So during installation, try to minimize the length of the pipeline within the allowable range of the design; On the basis of adjusting the power device, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.
The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
.Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, sports venues,LouisvilleHydraulic lifting platform and hydraulic lifting platform, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.
When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.
Many operating factories often require the use of hydraulic cargo elevators, which can be lifted and lowered, making it very convenient to use. Many people do not know the knowledge of hydraulic cargo elevator lifting and adjustment. If they understand this knowledge, it will be helpful for future maintenance. The power unit of the fixed chain elevator for hydraulic lifting of cargo elevators drives the hydraulic oil to generate pressure, causing the oil cylinder to move back and forth to drive the lifting platform, thus achieving the adjustment of lifting speed. The power unit adjustment, whether it is a scissor type lifting platform or a track type lifting platform is composed of the power unit and the oil cylinder. The power unit is manufactured with four outlet holes, which can be adjusted in size to increase or decrease the hydraulic oil flow rate of the oil cylinder, Adjustable motor speed or electro-hydraulic proportional valve to adjust hydraulic oil flow rate; The longer the oil pipe and hydraulic oil pipe, the longer the rise time. So during installation, try to minimize the length of the pipeline within the allowable range of the design; On the basis of adjusting the power device, the size of the oil pipeline can also be adjusted, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.
Installation material list.Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height,LouisvilleElevator Price, the larger the mass of the object, the greater the shaking
Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking, operations above 8 meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height, and intensity of high-altitude operations.
analysis.Load bearing capacity: The lifting platform is placed on a horizontal support surface and the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.
It must be abnormal. To solve the problem, the first step is to identify the cause of the problem. Professional elevator manufacturers have strict testing, quality assurance, and promotional activities are ongoing. Welcome to consult
The manufacturer of hydraulic cargo elevators reminds the use of guide rail hydraulic lifting cargo elevators. Guide rail hydraulic lifting cargo elevators: Do not stand within the specified range, prohibit any idle personnel from entering the work area, ensure that the work area is free of clothing, ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.
Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.