ToledoLifting platform hydraulic stationThe role of each component

Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, stations, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.

When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!

Toledo.Clean the surface of the base and install anchor bolts. If the construction elevator is installed on the floor, use a pad iron under the base screws to increase the force surface between the nut and the floor in order to reduce the impact of the nut on the floor; Insert steel plate gaskets of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite; After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and press it tightly

Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.

.Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color no bubbles, no cracks, and there should be no wrinkles, pits, paint leakage, and sagging.

Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, leveling, and alignment points, the greater the shaking. When using it at a working height of 10 meters, if possible, please use safety protection measures

If working on a grid like platform, wooden boards should be laid to prevent tools and equipment from falling.

Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.

quality index.Surface paint quality: The paint should be smooth and flat, have good adhesion with metal,ToledoScissor type hydraulic lifting platform, have uniform color, no bubbles, no cracks, and there should be no wrinkles, pits, paint leakage, and sagging.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.

The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.

The lifting platform is placed on a horizontal support surface,ToledoGuide rail hydraulic lifting platform, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.

Quality assurance.Lines of various safety equipment

The load of goods and the tonnage of goods transported at once also affect the lifting speed. The optimal value for transporting goods on a lifting platform is speed. If it is too heavy, it will affect the speed. The above is the knowledge about adjusting the lifting speed of hydraulic cargo elevators, hoping to be helpful to everyone. Long term improvement: The manufacturer has a complete range of products, excellent quality, and discounted prices

Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work as well as decoration, hotels, logistics, warehouses, supermarkets, etc. are commonly used in these situations, especially in the decoration industry. I have seen many decoration companies use small hydraulic cargo elevators, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, lifting speed, and height, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only 2 meters, and do not require many materials. He mainly promotes people, not goods, but not inferior to the use of other hydraulic cargo elevators. He is stable, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs,ToledoFreight elevator type hydraulic lifting platform, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.

Toledo.Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.

The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.

The use of cleaning oil and the brand used in the system