AnshanHydraulic fixed lifting platformHow to circulate and continue to develop

If there are problems inside the elevator and electrical professionals are present, any components of the hydraulic system should be disassembled and repaired in a completely depressurized condition.

Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, which can make the work relatively safer. When lifting the hydraulic lifting platform uses a dual protection structure, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.

When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.

.Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.

Troubleshooting: When the elevator power light is turned on, press the up button, the motor rotates, but the lifting platform does not rise. This may be due to the reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.

Small typesetting Copyright Shu ICP Bei No. 11019783-1

After 5000 hours of operation of the elevator, repair the mechanical and electrical systems.

When using, the weight should be evenly distributed, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.

In short, when using a fixed loading and unloading platform, there is basically no need to worry about stability, as the manufacturer has taken many measures in this regard,AnshanElectric lifting hydraulic platform, providing more guarantees so many times it can be used with confidence.

Online consultation.two

When the motor overheats, and after troubleshooting, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors,AnshanGrain unloading hydraulic mechanical platform, wiring,AnshanMobile hydraulic unloading platform, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.

Promotion.High stability of manufacturing materials. Usually, manufacturers can choose a variety of manufacturing materials when producing fixed loading and unloading platforms, and each material brings different effects when used. For many manufacturers in order to improve the stability of loading and unloading platforms during use, materials with high stability will be used as much as possible they attach great importance to the selection of manufacturing materials. Generally, as such materials can achieve better results in application.

It can be seen that the hydraulic lifting platform needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.

The above detailed introduction, I believe everyone has a certain understanding of elevator selection, so that they can have a clear goal when choosing, and then choose the elevator that is suitable for customers.

Anshan.High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.

The lifting stage can achieve the lifting of a double-layer tabletop. It can also be pieced into a stepped multi scenic, and multi-level staircase as needed,

The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.