Li ShiContaine
Li ShiPlatform
Li ShiContaineAdopting anti slip patterned steel plates, the platform has good anti slip performance.
Afterwards before the operation of the equipment (shè bè i), inspect the condition of the rotating grease (grease), check the condition of the rotating support gear (Gear), and immediately handle any abnormalities (ch ǔ l ǐ). Professional boarding bridge factory quality assurance, professional company, timely supply,Li ShiMobile lifting hydraulic boarding bridge, high cost-effectiveness, has become the preferred brand for many wire products, welcome to purchase!
Li Shi.The problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself, insufficient compression of the sealing ring, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found, Just replace it with a new one.
Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation
.Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.
2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.
The fixed hydraulic boarding bridge has three fundamental elements: purification, overheating, and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.
Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner
The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixed
Long term promotion to the axle factory, a 20 year old brand with competitive prices and guaranteed quality!
Direct labor.Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment,Li ShiMobile hydraulic boarding bridge, forklifts can directly enter the interior of the car compartment for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods. It can not only reduce your labor intensity, but also double the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.
The fixed hydraulic loading and unloading bridge is a specialized auxiliary equipment for fast loading and unloading of goods. Its height adjustment function allows a bridge to be built between the truck and the cargo platform in the warehouse. Forklifts and other transport vehicles can directly enter the truck for batch loading and unloading of goods, and only one person can work to achieve fast loading and unloading of goods. Boarding bridges reduces a large amount of labor for enterprises, improves work efficiency, and achieves greater economic benefits.
Precautions for safe use of fixed hydraulic boarding bridges When operating the machine, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, and do not overload or deviate. The rated load of the fixed hydraulic boarding bridge specified by the manufacturer is the total weight of the loaded goods and forklifts, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, which greatly improves the loading and unloading power (referring to the amount of work done by objects in a unit of time), and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework
Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge it is necessary to have a basic understanding of its basic knowledge. Below, fix it on both sides of the carriage first open the rear door of the truck Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable, a 20 year old brand with competitive prices and guaranteed quality!
In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.
It is understood that the mobile liquid boarding bridge is a specialized auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. The mobile liquid loading and unloading bridge is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. By using artificial hydraulic power, the height adjustment of the boarding bridge can be achieved without the need for external power supply. The adjustable length of the cable chain is used to hook the vehicle, which do not require inflation. It is sturdy and durable, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed tractors, which can easily and conveniently achieve traction movement.
Assuming that the manufacturing quality of fixed hydraulic boarding bridges is not satisfactory, the reasons for their shortcomings are mostly preventive repairs, and there are usually fewer elements of abnormal operation.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads,Li ShiSimple boarding bridge, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.