YongjiPit type
YongjiHydrauliwhen using a fixed loading and unloading platform, there is basically no need to worry about stability, so many times it can be used with confidence.
Check the rollers providing more guarantees, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Yongji.When using an electric lifting platform,YongjiMobile hydraulic lifting platform, there are many details that need to be noted, such as placing it on a flat surface during use to prevent tipping during work. In addition, what are the precautions for using electric lifting platforms?
Tail signature:
.The reduction gearbox, gearbox, external gear teeth, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.
The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
After 5000 hours of operation of the elevator, repair the mechanical and electrical systems.
When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
Tail signature:
Promotion.The reduction gearbox, gearbox, external gear teeth, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Copyright © 2006-2022 Yan-wei.Net.All Rights Reserved.
Using Help
where.Update Log
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
In short when using a fixed loading and unloading platform, there is basically no need to worry about stability,YongjiGkt12 hydraulic lifting platform, as the manufacturer has taken many measures in this regard, providing more guarantees, so many times it can be used with confidence.
Yongji.two
The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects,YongjiHydraulic pressure of lifting and lowering platform, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.
Hydraulic lifting platform is a non scissor type hydraulic lifting platform and is also a widely used vertical transportation equipment for goods, heavy chains are driven by oil cylinders to drive the lifting and lowering of hydraulic lifting platforms. It is also widely used for vertical transportation of goods between high-rise buildings. So, what are the advantages and characteristics of guide rail hydraulic lifting platforms?