HungaryMonoraiWith the continuous increase of our productivity and the continuous improvement of our lives, the tools used must be counted. After the maintenance is completed, the tools should be classified and organized, and counted to prevent the tools used for maintenance from being left inside the equipment, especially in the distribution box. When repairing the hydraulic system of the aluminum alloy elevator, it is necessary to keep the maintenance site clean and dust-free. When repairing and fastening screws for aluminum alloy elevators, it is necessary to use the correct diagonal first. When tightening screws, use a torque wrench to prevent excessive damage to the screws. After the maintenance is completed and before the power on test, it is necessary to count the number of maintenance personnel to ensure that there is no one inside the aluminum alloy elevator. This is very necessary for the maintenance of large fixed hydraulic elevators. After counting the number of people, inspecting and repairing the equipment and the maintenance site, the power transmission test can only be carried out. After the maintenance of the aluminum alloy elevator is completed, the equipment maintenance record must be filled out. The maintenance record should include the equipment maintenance date, the personnel participating in the maintenance, the maintenance items, the brand, model and specification of the replaced parts, the effectiveness of the maintenance, and whether the equipment still has problems after the maintenance is completed.
Hungary.The research and development direction of aluminum alloy elevators includes mechanical hazards such as moving parts, and other hazards.
Overloading or long-term eccentric loading operations are strictly prohibited, as this not only reduces the service life but also poses safety hazards.
.The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
After working for 10000 hours, the mechanical and electrical systems of the elevator will be overhauled.
Secondly, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall, leading to accidents. At the same time, replacing a new power unit also requires a certain cost.
. Before the maintenance of the hydraulic aluminum alloy elevator starts, the tools used must be counted. After the maintenance is completed, the tools should be classified and organized, and counted to prevent the tools used for maintenance from being left inside the equipment, especially in the distribution box. When repairing the hydraulic system of the aluminum alloy elevator, it is necessary to use the correct diagonal first. When tightening screws, use a torque wrench to prevent excessive damage to the screws. After the maintenance is completed and before the power on test, it is necessary to count the number of maintenance personnel to ensure that there is no one inside the aluminum alloy elevator. This is very necessary for the maintenance of large fixed hydraulic elevators. After counting the number of people, inspecting and repairing the equipment and the maintenance site, the power transmission test can only be carried out. After the maintenance of the aluminum alloy elevator is completed, the equipment maintenance record must be filled out. The maintenance record should include the equipment maintenance date, the personnel participating in the maintenance the maintenance items, the brand, model and specification of the replaced parts the effectiveness of the maintenance, and whether the equipment still has problems after the maintenance is completed.
Aluminum alloy elevators use hydraulic drive to drive the lifting platform, and many mechanical equipment uses this method for braking. This lifting braking method can generate a large amount of power and can load heavy goods.
Users can choose the power mode and configuration according to their usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine. Walking: assisted self-propelled, two wheel traction, self driving, and car modification. Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranked outriggers, and pull-out outriggers. System: explosion-proof electronic control system, remote control system, PIC system. Hydraulic pump station: domestic lifting platform dedicated pump station,HungaryTrack aluminum alloy elevator, imported pump station from Italy with external protective devices: organ cover type, mesh type, and iron plate sealed type.
Production department.Attention must be paid to the rotating parts of the aluminum alloy elevator. When the engine is running. Hands and tools must be kept away from rotating fan belts and fans. During the test drive it is necessary to be in a spacious area and ensure that the aluminum alloy elevator can safely stop and turn effectively.
Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
The garage door should be opened or the exhaust device should be opened. So that the exhaust gas can be stored in the garage at any time. Even if working outdoors. Also, do not stay near the exhaust pipe of the working engine for a long time.
Advantages: As a mobile device for high-altitude operations, aluminum alloy elevators have unique functions and advantages. Aluminum alloy elevators can be used indoors and outdoors making them convenient and fast. They can be used in a wide range of fields, ranging from construction to household grain transportation. Aluminum alloy elevators have always been supported by customers due to their unique appearance structure and durable and wear-resistant performance characteristics.
Analysis project.After 5000 hours of operation of the elevator, carry out medium maintenance on the mechanical and electrical systems.
The self-propelled aluminum alloy elevator has walking and steering driving functions, without the need for manual traction or external power supply. It is flexible and convenient to move, making high-altitude work more convenient and efficient. It is an ideal high-altitude work equipment for modern enterprise safety production. Able to walk quickly and slowly under different working conditions, simply
In low concentration carbon monoxide gas. It can cause symptoms such as headache, shortness of breath, body weakness and dizziness,HungaryDouble mast aluminum alloy lifting platform, psychological confusion, and even brain damage. In severe cases, it can cause death,HungaryAluminum alloy hand lift, such as starting the engine of the equipment in the garage.
Hungary.Hydraulic lifting platforms can be divided into: four wheel mobile, two wheel traction car modification, car type, auxiliary self-propelled, and lifting heights ranging from 4 meters to 18 meters. This series of products has a load capacity of 0.1 to 0.8 tons, and can also be customized according to user requirements, with a high load capacity of up to 10 tons.
Method: Check if the hydraulic oil in the mailbox is sufficient; Check if the oil filler cap of the fuel tank is excessively sealed, causing difficulty in oil pump suction. Check if the connection of the oil pump suction pipeline is loose to prevent air from the oil pump; Check whether the motor, cover, etc. are displaced, whether the fixing screws are loose, and whether the ambient temperature of the equipment used meets the specified usage conditions. Air, check whether the motor, cover, etc. are displaced, whether the fixing screws are loose, and whether the ambient temperature of the equipment used meets the specified usage conditions.
Method: Check the length or diameter of the power supply lead. When the wire length is not more than 25 meters, the wire diameter should not be less than 5m ². You can try fixing the plug directly to the socket without moving the cable.