Agnel sur Sein
Agnel sur SeinThe setting of the cable guide frame should comply with the user manual and regulatory requirements.
Use floor doors and cage door devices on construction sites where conditions permit.
Agnel sur Seine.Mobile electric elevators are divided into: four wheel mobile lifting platform, two wheel traction lifting platform car modified lifting platform, manual lifting platform, manual lifting platform, and AC/DC dual purpose lifting platform
The pump body adopts an integrated pump station, all equipped with imported high-quality pump stations, which can also be selected according to customer requirements to meet customer ideal requirements.
.Work is essential, and the main protective accessories include safety belts,Agnel sur SeineElevator manufacturer's electric elevator, guardrails, protective covers, platforms and stairs, etc.
Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position
The verticality of the guide rail frame should meet the requirements of the specifications.
Operating cost advantage and low failure rate: Due to the use of advanced hydraulic systems and good methods, the operating failure rate can be reduced to a low level.
The shutdown device (emergency stop switch) should be non automatic reset type.
When a rigid 5000mm2 square or circular flat surface is applied with a normal force of 600N to either side of the door, but safety should be maintained.
how much.Safety performance: Electric elevators not only have the safety device of traditional traction elevators, but also have an overflow valve to prevent excessive system pressure during upward movement
The spacing between wall brackets and the height of guide rails above the high attachment point should comply with the requirements of the user manual.
Safety grounding device. In order to protect against electrical equipment. The metal casing of electrical equipment and the metal structure of electric elevators should be equipped with a safety grounding device. The grounding wire should operate multiple wires, and the neutral wire should not be arbitrarily held as a safety grounding wire. Its grounding resistance should not exceed 4 ohms; The power supply of the electric elevator can be cut off.
The function of the lifting platform in a theater is roughly as follows: the main lifting platform arranged in the main performance area of the stage is mainly used to quickly change the scenery. Typically, with&quo; Product; In the music and dance theater stage arranged in a zigzag pattern, the lifting platform, side car platform,Agnel sur SeinePortable electric elevator, and rear car turntable perform a rapid transformation of the entire or partial scene. This arrangement allows for rapid switching of three full sets.
Direct material.Monthly maintenance and inspection of hydraulic lifting platform rollers, oil cylinder pin shafts and bearings, boom hinge shafts and bearings for wear. Add some oil to each part to extend the service life of the lifting platform bearings. The quality and level of hydraulic oil. The lifting platform should be raised throughout the entire process, and at this position, the hydraulic ground should be 40-50 millimeters higher than the bottom of the box. If the hydraulic oil becomes dark,Agnel sur SeineElectric elevators for construction sites, sticky, or has foreign objects such as gravel, it should be replaced in a timely manner (32 # hydraulic oil). Annual maintenance and inspection of all hydraulic pipelines and joints of the lifting platform. The pipeline must not be damaged, and the joints must not be loose. All joints must be tightened. Remove and disassemble the lowering valve of the lifting platform, blow out the plunger with compressed air, then install it and reinstall it. Drain and discard the hydraulic oil, remove the oil filter clean it with compressed air, and then return it to the oil tank and connect the pipeline.
Setting requirements: Construction electric elevators should be equipped with up travel (limit) switches.
Speed limiter. To prevent the driving speed from exceeding the normal speed. A speedometer should be installed (not required for floors below or including the second floor), which is an individual mechanism that is integrated with a safety clamp; The entrance and exit of the passenger compartment should be equipped with safety doors. Public places, family dormitories, and
Agnel sur Seine.When the wall bracket adopts non matching standard products, design calculations should be carried out.
Setting requirements: The verticality deviation of the installation of the guide rail frame of the construction electric elevator should comply with the requirements of the user manual and specifications, as specified in the above table.
Use floor doors and cage door devices on construction sites where conditions permit.