BogorT2 copper barFactors prone to stomata

Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects, welding defects, internal and external loads, stress concentration, corrosion defects and other factors, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage, corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding, forming, inspection and pipe expansion.

The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

Bogor. When stacking, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured, followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

.Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, bridges power station equipment, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

Use the medical copper tube table to eat. Because of the unique of the medical copper tube, when the oil drops on the table, it will only stick to the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer, and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, how to restore the appearance. Class For the processing of the appearance of some textured t2 medical copper tubes, pay attention to the bias, which is also called unidirectionality. For example, if the lines used are vertical rather than horizontal, STEP of the process used should be added, so the cost also needs to be added. Therefore, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil, machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, magnetic flux leakage detection process, surface inspection, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, there will be no obvious yield point, in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit, expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.

When cutting the copper pipe of air conditioner, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities and the W-shaped trend will fully emerge. In the second half of the year, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, and the market price has rebounded to around 7600 dollars per ton. Driven by this the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

First of all, we should set up a warehouse. The temperature in the warehouse should be generally kept at 15-30 ° C, while the humidity should be normal. The room should be kept ventilated.

Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example,BogorT2 copper bar, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the air conditioning copper pipes are used in construction,Bogor304 stainless steel round steel, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

Product line.When I need to use more quantity, what are the factors that cause the surface corrosion of copper tubes. Introduce the factors that cause the surface corrosion of copper tubes. Surface pollution: The oil, dust, acid, salt etc. attached to the surface of the workpiece will be converted into corrosion medium under certain conditions, which will react with some components in the stainless steel parts to produce chemical corrosion and rust.

Some problems. For example, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured, followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

Generally speaking, professional t2 copper tube manufacturers will adopt an integrated molding process to improve the yield and reduce production costs while packaging products with superior performance. As long as the above t2 copper tube quality identification method is used it is basically guaranteed to purchase t2 copper tubes with reliable quality. If long-term and large-scale procurement is required, it is recommended to go to the manufacturer for field inspection to determine the basic performance and quality of t2 copper tubes before large-scale mold procurement. The position of grid accessories plays a very important role in the whole construction process. The products with high cost performance and good performance certainly have a great assistance effect for the implementation of the project. In addition, it is also beneficial to the application of the middle and later stage of the forming project. There are high regulations for the performance of the grid. How about the corrosion resistance of the grid accessories? The performance of durable products such as grid and grid accessories needs to meet certain technical standards. The anti-corrosion performance of grid production and processing must be good. For manufacturers, the anti-corrosion performance of accessories is not very good. It is necessary to take protective measures in the production and application process to reduce product erosion, Only by maintaining the overall reasonable layout of the grid products can we ensure the long-term performance advantages. Many technologies are required in the whole process of production and manufacturing of space truss accessories. The production and manufacturing staff should ensure the performance advantages when carrying out production and manufacturing of products. The production and processing of space truss should improve its corrosion resistance, compression resistance and strength to ensure that qualified products are produced by the original factory.

How much does it cost?.I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

Save materials and total cost, stability and performance and can save maintenance.

The editor of this website of t2 Medical Copper Tube Company said that if there is no table, they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools, while wooden tables can often be found in small restaurants as one of the steel products of medical copper tubes. As his name is common, medical copper tubes have the ability to prevent rust. In the catering industry, tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large, and the number of tables is amazing, it will cost a lot of money, and it will also take a lot of work to settle after eating.

Bogor.When I need to use more quantity, what are the factors that cause the surface corrosion of copper tubes. Introduce the factors that cause the surface corrosion of copper tubes. Surface pollution: The oil, dust, acid alkali, salt, etc. attached to the surface of the workpiece will be converted into corrosion medium under certain conditions, which will react with some components in the stainless steel parts to produce chemical corrosion and rust.

In addition, brass has a unique sound so the gongs, cymbals, bells, horns and other instruments in the East, as well as the western brass instruments, are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, silicon, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, an appropriate amount of iron, nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.

In addition, brass has a unique sound, so the gongs, cymbals, bells, horns and other instruments in the East, as well as the western brass instruments, are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, it should be pointed out that the alloy composed of iron, silicon, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition,BogorCopper tube, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch, good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, an appropriate amount of iron, nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.