ColmarMobile hydraulic unloading platformWhy need reinforcement-World information network

The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!

Colmar.In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, it is necessary to stop the motor in a timely manner, and then troubleshoot the problem before continuing to use it. This way, the motor shaft can be used and the effect is good.

When conducting high-altitude operations on dangerous edges such as roofs suspension bridges, slopes or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.

.Remove trailing spaces, remove first and last interfering characters, remove blank lines, remove non paragraph blank lines, punctuation correction: Leading space type: Number of spaces:

The brakes of each mechanism should be regularly checked and adjusted for the clearance between the brake pads and brake wheels to ensure flexibility and reliability. There should be no dirt on the friction surface. If there is dirt, it must be cleaned with gasoline or rare materials.

Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.

When a hydraulic lifting platform malfunctions blow the valve core clean with compressed air, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time,ColmarFixed hydraulic lifting platform,ColmarHydraulic lifting platform, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.

Then, the lifting platform platform platform that carries the load needs to be balanced, and no deviation of one side is allowed. The lifting of goods does not allow people to stand on both sides of the platform, and the lifting of goods should try to maintain a stable and uniform speed.

Installation material list.Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection, the safety factor of the guide rail hydraulic lifting platform is still very high,ColmarMovable hydraulic lifting platform, much higher than that of ordinary platforms.

Function: Convenient unloading, strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms and unloading platforms: anti slip devices: This device is welded from steel plates and can effectively achieve anti slip function, which is reliable.

Update Log

ColmarMobile hydraulic unloading platformWhy need reinforcement

Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and tighten it if there is any looseness

The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.

Of course, when choosing a lift, it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength, especially the construction lift has relatively high requirements for production technology. Therefore, when making a purchase, it is important to consider the factory building and process of its production, all of which are very important.

Colmar.The purpose of the stage elevator: The telescopic stage adopts an effective guidance system, which reduces the gap between the telescopic stage and the fixed stage during the translation process, ensures smooth operation, and continuously changes speed. The synchronous device adopts a low speed and large torque drive, making the stage parallel, free, and retractable in place during the stretching process, and can automatically achieve leveling. Suitable for cultural and entertainment venues such as halls, cinemas, multifunctional halls, studios, cultural sports venues, hotels, etc.

Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.

When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.