Guenzburg Indo
Guenzburg HydrWhat are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
When encountering overheating in the hydraulic elevator motor, it is necessary to stop it in a timely manner, eliminate the fault, and continue running. The motor bearings should be in good condition.
Guenzburg .Check the starter potential when the lifting table is not raised or the voltage is too low when the motor load is working. Voltage hydraulic range allowed± 10% of the motor does not rotate. Check the motor and circuit. The motor can be reversed to arbitrarily change the two phases in the three-phase line.
The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, eliminate faults, and achieve these benefits for improving work efficiency, extending equipment service life, and ensuring the safety performance of the elevator.
.Any product always has a break-in period when it is first used, the editor will share this topic with everyone.
Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.
Guide rail type cargo elevators are a type of equipment for transporting heavy objects up and down, and have great applications in factories, workshops, and other places. For this type of heavy machinery, its daily maintenance and upkeep are very important, attention should be paid to the daily maintenance of cargo elevators.
Any product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.
The reason for the price of aluminum alloy lifting platforms is that hydraulic pumps are also a factor affecting the flow of hydraulic oil. Using hydraulic pumps that have been used for too long can easily lead to problems. When the speed of the hydraulic elevator platform slows down, it is necessary to check whether the oil supply flow rate of the hydraulic pump remains unchanged. If there is an invention problem, contact the manufacturer in real time to avoid exceeding the warranty period.
The load capacity of goods and the tonnage of goods transported at once also affect the speed of lifting and lowering. Achieving the excellent value of the lifting platform for transporting goods is a guarantee of speed. If the weight is too heavy, it affects the speed. If the goods are too light, it also affects the normal transportation time.
Inspection basis.Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.
Installing bearings for elevators may seem simple, but it is also important to pay attention to some details, such as: it is actually difficult to thrust bearings into the shaft pins when excessively installing them. However,Guenzburg Price of hydraulic platform lift truck, some people may think of using a hammer to hammer the bearings for convenience, and use brute force during installation. In fact, directly hitting the bearings with a hammer can cause significant damage to the bearings, which is the main reason for bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
How to install and use the bearings of the elevator? During the process of using the bearing device of the elevator, we cannot always ensure that the bearing device has the right orientation, which inevitably leads to some devices not being in place or bearing displacement. Once these problems occur in the device, it will cause the clearance between the bearings to become too small, and then make it impossible for the inner and outer rings of the bearings to be in the same rotation center. So it is necessary to use specialized tools when installing bearings, and in the future, it is also necessary to use a testing instrument to test the bearing installation, in order to ensure the success of the bearing installation.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated. For a long time, the manufacturer of scissors lift has never changed hands to avoid price difference, and the price is 20% higher than the market value! More than one ton is more expensive!
Quality improvement.Do not adjust the solenoid valve on the motor arbitrarily. The solenoid valve is pre adjusted before leaving the factory, and random adjustment can easily cause internal pressure to increase or decrease. In severe cases, it can shorten the service life of the motor.
How do elevator manufacturers maintain and maintain construction elevators? In order to accurately implement the equipment maintenance system it is necessary to establish a mechanical management responsibility system; It is necessary to develop maintenance procedures for different models; Corresponding maintenance institutions must be implemented; It is necessary to handle the relationship between maintenance and production, so as not to affect production or equipment maintenance.
Motor does not rotate: The motor is broken, and the manufacturer will handle it. We are a long-term manufacturer of scissor type elevators. Welcome to inquire
Guenzburg .After careful inspection it was found that it was mainly caused by two reasons
The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%. Specializing in product and renewable resource business, including: scissor lift manufacturers
Familiarity with the usage process and without a doubt, this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, during the running-in period, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn, and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, there is no need to worry in the early stage. If there are no major problems,Guenzburg 3-meter hydraulic lifting platform, run it several times more. After the running-in, the noise will naturally disappear. However, if there is noise for a long time and no signs of fading, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints, etc. If there are any, please reinforce or replace them in a timely manner to avoid accidents.