Schigerzent mi
Schigerzent miOil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, when all hydraulic cylinders in the system are extended, the oil level should not be higher than the Z-high oil level. In fact most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
Schigerzent michlos.Due to the formation of a flow closed-loop the volumetric speed regulation hydraulic elevator has good performance and high load stiffness. The hydraulic system using the volumetric speed regulation scheme has a higher efficiency and greater energy loss compared to the throttling scheme, as its output power is roughly equal to the power required for the elevator to move up. But using an elevator volume speed control system can only reduce the energy consumption during the upward process of the elevator. When the elevator goes down, the oil in the cylinder moves down the throttle valve under pressure, which will cause the temperature of the hydraulic system to rise. Not to mention anything else just an intelligent alarm is enough to demonstrate the true value of hydraulic elevators.
Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.
.Mobile is a type of cargo heavy machinery equipment with good adjustment reliability and wide application fields, suitable for automated production lines
. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. In order to ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve and balance circuit are installed on the return oil circuit to maintain pressure and ensure that the descent speed is not affected by changes in heavy objects. The throttle valve regulates the flow rate and the lifting speed. To ensure safe and reliable braking and prevent accidents, a hydraulic one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking when the hydraulic pipeline bursts. Install an overload sound alarm to distinguish between overload or equipment failure.
The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile,Schigerzent michlosElectric hydraulic fixed lifting platform, guide rail and curved arm types. Fixed types include scissor elevators, loading and unloading platforms, and attached electric construction platforms.
Remember not to overload, only clean plastic plugs can be used to seal the end of the pipeline.
Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, and there should be no leakage at all components, pipelines, and joints.
Test results.The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
Lines of various safety equipment
To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.
The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Direct labor.When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
When maintaining hydraulic components, the workbench must be clean. The purpose of the inspection tool.
When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
Schigerzent michlos.Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However, there are still certain limitations, such as height and improving the quality of goods,Schigerzent michlos5 ton hydraulic lifting platform, which have certain constraints.
Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation,Schigerzent michlosScissor fork hydraulic lifting platform, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.
The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection increase stability, and reduce shaking.