MiddleburgOutdSecondly, there should be no dirt on the friction surface. If there is any dirt, it should be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; Correct maintenance of the hydraulic guide rail elevator: Regularly inspect the wire ropes at various parts for broken wires and looseness. If any such phenomenon is found, replace it in a timely manner. The maintenance of the wire ropes must be carried out in strict accordance with the specifications; Check the connection condition of each part according to the braking rules and regulations. If there is any looseness, tighten it in a timely manner. Check the tightness of the connecting bolts of the equipment when the body is under pressure. All connecting shafts should be equipped with cotter pins; Check whether the operation of each mechanism is normal, whether there are noises and faults according to regulations, and promptly remove all faults; When installing, disassembling, and adjusting the rotating mechanism of the equipment, it is important to note that the reducer and the gear center line should be parallel and the meshing clearance should be appropriate; Regularly conduct a comprehensive inspection of the equipment to see if there is any damage to the wires and cables, and if there is overheating of the motor. Replace the motor in a timely manner and eliminate the fault before continuing operation; Ensure that the bearings, boxes, distribution boxes, and brushes of the motor are kept clean, and that the travel switch points of each safety device must be safe and reliable.
The water cooling of hydraulic stations is generally tubular water cooling, and the type selection is based on the heat load to calculate the heat exchange area, while the air-cooled elevator is conducted using an air cooler,MiddleburgGuide rail lifting cargo elevator lifting, and the heat exchange capacity is calculated based on the heat load. Then, the type selection calculation is performed when the flow can be satisfied. Therefore, the two types of cooling are different, and there are significant differences. Long-term lifting and lowering of cargo elevator factory
Middleburg.In fact, it is also important to pay attention to some details, as follows: It is actually difficult to pierce the bearings into the shaft pins when excessively installing them. However, sometimes, some people think of using a hammer to hammer the bearings to facilitate the installation, and use brute force during installation. In fact, directly striking the bearings with a hammer can cause significant damage to the bearings, which is the main reason for causing bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
Several types: motor winding open circuit. When one phase of the motor winding is open circuit, or one of the parallel branches is open circuit, it will cause three-phase current imbalance and cause the motor to overheat.
.Motor connection error. When the triangular connection motor is mistakenly connected into a star shape, the motor still operates with full load, leading to the motor stopping itself. If the stopping time is slightly longer and the power supply is not cut off,Middleburg3 ton fixed lifting cargo elevator, the winding will not only be severely overheated, but also burned. When a star connected motor is mistakenly connected into a triangle, or when several coil groups are connected in series into a single branch, the motor is mistakenly connected into two branches in parallel, both the windings and the iron core will overheat and in severe cases,MiddleburgWarehouse elevator, the windings will be burned.
Large logistics warehousing equipment service company with guaranteed prices and guaranteed services, directly operated by the manufacturer. Because fixed elevators are mechanical equipment, the quality and performance of the product are good. Do not accept products from some manufacturers that do not meet the quality standards, in order to avoid some safety hazards in use.
What types of elevators are there? There are many types of such equipment, such as fixed lifting devices and vehicular lifting devices, depending on the form of movement. The so-called fixed lifting is generally installed in one place and fixed and then lifting operations can be carried out. This type of lifting equipment is generally used more on the assembly line, and some large production lines need to lift the materials to a certain position when loading them, and then put them into production on the production line. A special lifting device needs to be fixed at a certain position on the production line.
The hydraulic lifting platform can be divided into four wheeled mobile type, two wheeled traction type, vehicle modified type, vehicle type, auxiliary self-propelled type, and the lifting height varies from a meter to 1 meter.
The solenoid valve on the motor should not be adjusted randomly. The solenoid valve is pre adjusted before leaving the factory, and random adjustment can easily cause internal pressure to increase or decrease, which in severe cases can shorten the service life of the motor.
Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranking outriggers and pull-out outriggers.
Inspection requirements.Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Before installing the elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of each part connecting the motor and the elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
When a cargo elevator fails, it should be repaired by professional personnel. It is not allowed to modify the cargo elevator without permission.
Purpose The hydraulic lift is widely used in various industrial enterprises and production lines such as automobile, container, mold manufacturing, wood processing chemical filling, etc., to meet the lifting requirements of different operation heights, and can be equipped with various table forms (such as ball, roller, turntable, steering, tipping, and with various ways (separate, linkage, explosion-proof), it has the characteristics of stable and accurate lifting, frequent starting, and large load capacity, Effectively solve various lifting and lowering operation difficulties in industrial enterprises, making production operations free. Professional elevator factory has advanced technology, more affordable prices, and more preferential treatment. Welcome to consult
Word of mouth recommendation.Test the goods elevator every day to see if it can operate normally.
Although the cargo elevator has good safety, in actual work, if you do not pay attention to detailed maintenance there may be accidents, so we should pay attention to it when performing daily maintenance.
Characteristics of hydraulic elevators: Hydraulic lifting platform products are divided into curved arm type hydraulic lifting machines, scissors type hydraulic lifting machines, and straight arm type hydraulic lifts according to their working modes. Hydraulic elevator is a replacement product of folding arm elevator (lifting platform) and scissor fork elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks, airports, hotels, municipal gardens, garages, cleaning companies, public building facades, or the installation and maintenance of power systems, etc. This elevator has the advantages of light weight, self-propelled walking, electric starting, self supporting legs, simple operation, large working area, and especially the ability to cross obstacles for aerial work.
Middleburg.Scissor type fixed lifting platform is a transportation and loading equipment that transports goods from one height to another. After operation, the platform is level with the ground, without occupying ground space and affecting passage passage.
Fixed elevator is a transportation equipment that directly lifts and loads goods from the ground. It is mainly used for goods transportation between height differences in production lines, material loading and unloading, component lifting during assembly of large equipment, fixed three-dimensional parking, and other places. So what is the new price for fixed elevators?
In addition to having a fixed mode, there are also types of mobile elevators. As the name implies, it is a combination of lifting equipment and on-board systems. This type of lifting equipment is very flexible to move, it is better to use it. For example, there are such lifting equipment in airports, The scope of work is not limited to a certain place as it can be moved by itself, but can be used wherever lifting operations are required. For example, when installing outdoor advertisements, some advertisements are relatively high in height. At this time, mobile lifting equipment can be used to send billboards or staff to a designated height for work. This type of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is the use of hydraulic oil to drive to achieve a specified height. The electric mode is driven by a motor or tooth to lift to a certain height. However, currently, hydraulic lifting platforms are more widely used.