AltamuraElectr
AltamuraSmall Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
If hydraulic elevators are used on campus, it can better enhance the safety and security of the campus. For campuses, especially after school every day, there are a large number of parents and there are also safety hazards such as people and cars. Maintaining order in such situations is a good idea.
Altamura.When using hydraulic elevators check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!
.The pressure lifting platform adopts a double four bar mechanism to achieve the lifting and flipping of the vehicle mounted cargo elevator platform, and a complex self-locking mechanism to achieve automatic opening and closing of the baffle. In order to reduce driving force, multiple sets of pulleys are used to achieve motion transmission and smooth movement on both sides of the lifting device. The hydraulic lifting platform adopts a hydraulic power unit transmission method, making the lifting more stable and the service life longer.
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil,AltamuraHydraulic lifting platform factory,AltamuraAutomatic hydraulic unloading platform, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors,AltamuraHydraulic rotary platform, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
The following is a brief description of the precautions for using high-altitude work platforms: high-altitude workers must hold a health certificate. Individuals with mental illness hypertension, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.
Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Firstly, safety devices to prevent overloading, multiple limit switch protection, leakage protection, and multi-layer building interaction. Therefore the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.
Quality risk.Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
Tail signature:
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
Using Help | Updating Logs | Original Software | Daily Software
Finance Department.Leading spaces in blank lines Full width: Font size: Replace: Replace
The characteristics of hydraulic lifting platforms are obvious, such as their relatively light overall weight and good maneuverability, allowing even a single person to operate, making them relatively suitable. The mast columns of its system are equipped with guide wheels so its lifting and lowering are relatively stable during use. Of course, attention should also be paid to the structure of the hydraulic lifting platform to ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
Head signature:
Altamura.The brakes of each mechanism should be regularly checked and adjusted for the clearance between the brake pads and brake wheels to ensure flexibility and reliability. There should be no dirt on the friction surface. If there is dirt, it must be cleaned with gasoline or rare materials.
For homepage | add favorites | email | QQ: If you have any questions, please QQ us!
When we use hydraulic elevators in our daily lives, we need to regularly inspect and maintain them. This not only extends the lifespan of the hydraulic elevators, but also allows them to exert greater power in their work. For example, the transmission part requires sufficient oil, and consuming components must be regularly inspected, maintained, or replaced. Mechanical bolts, especially those that frequently vibrate, such as rotating supports and lifting arm connecting bolts, must be tightened or replaced immediately when they become loose. Next, the editor will introduce how hydraulic elevators should be maintained.