KararaHydrauli
KararaLuxury h
KararaHydrauliIf there are problems inside the elevator and electrical professionals are present, any components of the hydraulic system should be disassembled and repaired in a completely depressurized condition.
Secondly, the maintenance of the guide rail type hydraulic lifting platform is also very simple, using oil cylinders and chain transmission, with very few moving components, so the maintenance workload is not very high. Moreover, resulting in a longer service life.
Karara.Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms,KararaElectric hydraulic loading and unloading platform, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform carries people during use, it is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
If hydraulic elevators are used on campus, it can better enhance the safety and security of the campus. For campuses, especially after school every day, there are a large number of parents and there are also safety hazards such as people and cars. Maintaining order in such situations is a good idea.
.Remove trailing spaces, remove first and last interfering characters, remove blank lines, remove non paragraph blank lines, intermediate shafts repair the mechanical and electrical systems.
Check the rollers and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Remove trailing spaces, remove first and last interfering characters, remove blank lines, remove non paragraph blank lines, punctuation correction: Leading space type: Number of spaces:
Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
The reduction gearbox, gearbox,KararaHydraulic lifting platform Hydraulic platform, external gear teeth, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.
Home page recommendation.Small typesetting Copyright Shu ICP Bei No. 11019783-1
When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.
Leading spaces in blank lines Full width: Font size: Replace: Replace
The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.
install.Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.
When a hydraulic lifting platform malfunctions it is necessary to take time to prepare accordingly. At this time,KararaRaise the hydraulic platform, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
Outdoor elevators and factory cargo elevators are heavy lifting mechanical equipment. Outdoor elevators are used for transporting goods between floors of buildings, and are specialized hydraulic cargo elevator products. They are mainly used for transporting goods up and down between various working floors; Vertical garage and car lift between garage floors. The hydraulic system of the product is equipped with anti fall and overload protection devices, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point operation.
Karara.Of course, when choosing a lift, it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength, especially the construction lift has relatively high requirements for production technology. Therefore, when making a purchase, it is important to consider the factory building and process of its production, they must be promptly eliminated.
two