GottingenVehic
GottingenSmall
GottingenHydraDrain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
Original software
Gottingen.When a hydraulic lifting platform malfunctions, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
The above detailed introduction, I believe everyone has a certain understanding of elevator selection so that they can have a clear goal when choosing, and then choose the elevator that is suitable for customers.
.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
The reduction gearbox, gearbox, external gear teeth and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.
Regularly check the connection of each part, and tighten it if there is any looseness
Website homepage
Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
The product has a sturdy structure it is equipped with railings or anti crack valves, a large load-bearing capacity, smooth lifting, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.
Superior quality.The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures,GottingenHydraulic boarding platform, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform,GottingenManufacturer of automatic hydraulic lifting platform, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.
Hydraulic loading elevators must strictly carry out load-bearing operations in accordance with regulations. Otherwise, it may harm people and objects!
Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection,GottingenSmall electric hydraulic lifting platform, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.
Later, when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs, it should not be used again to avoid accidents, personnel and property losses.
Good quality.The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Regularly check the connection of each part and tighten it if there is any looseness
Gottingen.The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.
When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.
The pressure lifting platform adopts a double four bar mechanism to achieve the lifting and flipping of the vehicle mounted cargo elevator platform, and a complex self-locking mechanism to achieve automatic opening and closing of the baffle. In order to reduce driving force, multiple sets of pulleys are used to achieve motion transmission and smooth movement on both sides of the lifting device. The hydraulic lifting platform adopts a hydraulic power unit transmission method, making the lifting more stable and the service life longer.