YunchengMovabl
YunchengBoardiThe length of the electric hydraulic boarding bridge is generally about 10 meters, and the bearing weight varies depending on the tonnage. It is 10500mm for 6 tons, 11200m for 8 tons, and 11300m for 10 tons. It is very suitable for placement on the ground in open spaces.
Reasons for the hydraulic boarding bridge lifting platform not lifting: low voltage, motor not rotating, motor reverse, motor phase loss (motor not moving and buzzing), press the up button, motor rotates but lifting platform does not rise, lowering valve is open, overflow valve pressure is low,YunchengMobile hydraulic boarding bridge, oil level is too low, oil pump is empty, oil suction filter is blocked, oil suction section is leaking, and two phases in the three-phase line are arbitrarily changed; Solution: Check the starter potential during motor load operation. Voltage hydraulic range allowed± １０％； Check the motor and circuit; Check the circuit breaker and motor wiring; When the lowering button is released, use a voltmeter to check whether the lowering valve is energized. If there is no power, check the circuit and eliminate the fault; If there is electricity, eliminate the malfunction of the lowering valve itself. The slide valve of the lowering valve must be kept clean and move flexibly. Readjust the overflow valve. Adjust at 100% rated load; Fill up the hydraulic oil; Clean the filter; Check the oil suction pipe and joints; Tighten the joint and replace it if necessary.
Yuncheng.Function: Convenient unloading strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platform vehicles, lifting platform vehicles, and unloading platform vehicles: Anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is reliable.
conduct.
.Open the manual valve, slowly lower the boarding bridge, and secure more than 90% of the lip plates at the bottom of the container.
Portable hydraulic press boarding bridge: It is a widely used type, suitable for places where loading unloading, and transportation are not fixed or moving; Mobile hydraulic press boarding bridge: suitable for fixed and immovable goods such as ports, cargo platforms, warehouses, etc
Common&quo; Streamline” Open joint planning, and the bearing weight varies depending on the tonnage. It is 10500mm for 6 tons, 11200m for 8 tons, and 11300m for 10 tons. It is very suitable for placement on the ground in open spaces.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
Tighten the manual valve to close it.
Total quality management.Install a 5m high protective railing around the foundation pit of the simple boarding bridge, with a distance of no less than 1m from the protective railing to the foundation pit. The mobile boarding bridge only requires a single person to operate, without the need for power supply, and can achieve safe and fast loading and unloading of goods. Mobile boarding bridges are widely used in cargo platforms and mobile loading and unloading sites without loading and unloading equipment. They are auxiliary equipment for cargo loading and unloading that is used in conjunction with forklifts. The sequence of earthwork excavation must comply with design conditions and follow" Trenching support, support first and then excavation, layered excavation, no overbreak&rquote; The principle of.
conduct.
The pressure on the axle will reduce the service life of the boarding axle.
When the hydraulic oil is insufficient, the hydraulic pump will produce suction phenomenon, causing air to enter the hydraulic oil and also producing high noise. The boarding bridge is already a very visible structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.
Recommendation and consultation.The correct operation of the hydraulic boarding bridge is good maintenance and how to operate it correctly. Let me briefly introduce the operating steps of the hydraulic boarding bridge, hoping to bring more help to everyone.
There are many types of boarding bridges, and their respective roles and application fields are also different. Hydraulic boarding bridges,YunchengProcurement of fixed boarding bridges, fixed boarding bridges, and mobile boarding bridges are currently common and advantageous equipment on the market, playing a huge role in their respective fields. Below, we will first analyze the development trend of mobile boarding bridges: mobile hydraulic boarding bridges are a good helper for loading and unloading goods on forklifts. Compared to pneumatic tires, mobile boarding bridges are equipped with solid tires with low starting resistance, simple structure, convenient use and maintenance, no need for inflation, no hidden dangers of air leakage and tire explosion. And solid tires have good safety, durability, puncture resistance, tear resistance, and economy.
Monthly maintenance of hydraulic boarding bridges: check for wear on rollers, intermediate shafts and bearings, cylinder pins and bearings, boom hinge shafts and bearings, etc; The oil quality and level of hydraulic oil; The hydraulic boarding bridge should be raised throughout the entire process, and at this position, the hydraulic surface should be 40 to 50 millimeters higher than the bottom of the box. The hydraulic oil is darkened, sticky, it should be replaced in a timely manner; Add some oil to each part to extend the service life of the bearing. The hydraulic boarding bridge has a wide range of uses. Doing the above points well not only ensures your personal safety but also extends the service life of the equipment,YunchengHydraulic boarding bridge factory, making the boarding bridge better serve you.
Yuncheng.Common&quo; Work” Steel structure planning can withstand uniform pressure, reduce skeleton torque, and be more robust than other channel structures.
During use, close attention should be paid to the condition of the equipment, and if there are any problems, the use should be stopped immediately.
To ensure that the hydraulic boarding bridge is in good condition, it should be checked in advance before use, press the up button, the motor rotates but the lifting table does not rise. This may be due to the reverse connection of the three-phase power supply and the motor reversing. Only the power supply needs to be corrected so it is not a major problem.