SavonaMobile hThere is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.
Savona.The manufacturer of hydraulic cargo elevators tells you the precautions for high-altitude operations.
After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.
.When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.
Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch it should be suitable for the operating power.
The above are common situations, and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.
Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height, the greater the shaking. When using it at a working height of 10 meters if possible, please use safety protection measures
Recommendation and consultation.After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.
Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
Sincere service.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.
The manufacturer of hydraulic cargo elevators tells you the precautions to be taken when installing hydraulic cargo elevators. Hydraulic cargo elevators work using hydraulic systems and are usually used for the transportation of large goods. Hydraulic cargo elevators are different from traditional shelf elevators. They use a new hydraulic system to reduce the occurrence of faults and utilize their own weight to reduce energy consumption when lowering goods. So,SavonaElevator Price, what should be paid attention to when installing hydraulic cargo elevators? The hydraulic cargo elevator manufacturer is here to tell you!
When installing, disassembling, and adjusting the rotating mechanism attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, with an allowable fluctuation range of± 10%.
Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.
After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.