TaochengHydraulic lifting platformCheap manufacturers offer

the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.

Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.

Taocheng.Lift and move horizontally with load to return to the loading position. For the transportation time of each item, such repeated cycles are called cycles.

Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.

.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, and sleeve type lifting platforms according to their different modes of movement.

Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity, clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.

Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.

When installing, disassembling,TaochengHydraulic scissor type lifting platform, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.

There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature,TaochengHydraulic lifting platform supplier,TaochengScissor fork hydraulic lifting platform, the volume will change, which is reflected in the lowering of the position on the table.

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

Discount.The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.

To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color, no bubbles, no cracks, and there should be no wrinkles, pits, paint leakage, and sagging.

Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.

new product.The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.

The machine room can be located within a radius of 15 meters of the shaft, occupying only 3-4 square meters. Professional improvement of quality assurance for aircraft manufacturers. The promotional activity is ongoing, and new and old customers are welcome to come for consultation

Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.

Taocheng.To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.

To consider its capacity, and fixed equipment takes 3-4 times.