OstrovinkaType
OstrovinkaFixeSeparate: Loading and unloading on different platforms.
Stable and widely applicable cargo lifting equipment is mainly used for transporting goods between height differences in production lines; Material online and offline; Adjust the height of the workpiece during assembly; High altitude feeder feeding; Lifting of components during assembly of large equipment; Large machine material and cutting; The warehouse loading and unloading site is equipped with forklift and other transportation vehicles for rapid loading and unloading of goods.
Ostrovinka.Cleaning and maintenance: When there is oil in the oil tank or when oil is refilled, it is necessary to ensure the cleanliness of the filter tank cover. Clean the oil and funnel or container before use. Never bring dirty things into the system, only clean oil.
The hydraulic oil used in the system has the same brand,Ostrovinka20 meter hydraulic lift, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
.The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.
When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
Based on experience new steel wire ropes will not suddenly break when used under normal circumstances, unless incorrect operation or safety protection devices fail, as the load borne by the steel wire may exceed its breaking capacity. The damage to the steel wire rope of the cargo elevator is mainly gradually formed during long-term use. After a certain period of repeated bending and friction, the steel wire on the surface of the steel wire rope will experience bending fatigue and wear, and the steel wire on the surface layer will gradually break. At this point, if it cannot be used again, it should be replaced in a timely manner to ensure the safety of the hydraulic platform.
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
Where can I find it?.Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings airports, stations, sports venues, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.
Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators to avoid any worries about after-sales service.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
technical service.The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more,OstrovinkaSmall hydraulic lifting platform, and after each cleaning,OstrovinkaMobile hydraulic lifting platform, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
Below, we will analyze for everyone. According to the market survey and understanding conducted by the editor of hydraulic freight elevator manufacturers, many customers choose hydraulic elevators instead of elevators due to the following reasons: narrow transportation location, which cannot meet the requirements of elevators; Unable to excavate the elevator shaft at the working location; Elevators are expensive and difficult to meet their needs.
Hydraulic lifting table: the hydraulic lifting table is widely used in various industrial enterprises and production lines such as automobile, container, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operation heights, and can be equipped with various table forms (such as ball, roller, rotary table, steering, tipping, telescoping), and with various ways (separate, linkage, explosion-proof), it has stable and accurate lifting, frequent starting The characteristics of large load capacity effectively solve various lifting and lowering difficulties in industrial enterprises, with an allowable fluctuation range of± 10%.
Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.