New OrleansHyd
New OrleansHydThe above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump,New OrleansScissor fork hydraulic lifting table, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.
New Orleans.There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature,New OrleansHydraulic lifting platform, which is reflected in the lowering of the position on the table.
Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.
.Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.
Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Lift and move horizontally with load to return to the loading position. For the transportation time of each item, such repeated cycles are called cycles.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
Installation works.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment leveling,New OrleansScissor type hydraulic lifting platform, and alignment points, and confirm that the foundation meets the requirements before construction.
Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
The elevator itself has a simple structure and is easy to maintain which has been favored by a large number of enterprises and individual customers. Hydraulic elevator is a multifunctional heavy loading and unloading mechanical equipment. The lifting system of hydraulic elevators is driven by hydraulic pressure, also known as hydraulic powered elevators.
The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators chain elevators, loading and unloading platforms, and attached electric construction platforms.
Development Curriculum.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
Compare the measurement curves and then go to the variable displacement pump or variable speed motor. Long term targeting all types of high-priced elevator manufacturers nationwide with reasonable prices and comprehensive services, we have gained recognition from our customers
When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.
New Orleans.To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.
Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.