Zory Scissor f
Zory Customize
Zory Fixed eleThe classification of lifting platforms is as follows: they are divided into mobile lifting platforms, folding arm lifting platforms hydraulic lifting platforms, and sleeve type lifting platforms according to their different modes of movement.
Lines of various safety equipment
Zory .Many operating factories often require the use of hydraulic cargo elevators, which can be lifted and lowered, making it very convenient to use. Many people do not know the knowledge of hydraulic cargo elevator lifting and adjustment. If they understand this knowledge, it will be helpful for future maintenance. The power unit of the fixed chain elevator for hydraulic lifting of cargo elevators drives the hydraulic oil to generate pressure causing the oil cylinder to move back and forth to drive the lifting platform, thus achieving the adjustment of lifting speed. The power unit adjustment, whether it is a scissor type lifting platform or a track type lifting platform, is composed of the power unit and the oil cylinder. The power unit is manufactured with four outlet holes which can be adjusted in size to increase or decrease the hydraulic oil flow rate of the oil cylinder, Adjustable motor speed or electro-hydraulic proportional valve to adjust hydraulic oil flow rate; The longer the oil pipe and hydraulic oil pipe, the longer the rise time. So during installation, try to minimize the length of the pipeline within the allowable range of the design; On the basis of adjusting the power device, the size of the oil pipeline can also be adjusted, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.
.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.
How to maintain the cleanliness of hydraulic elevators. If more high-quality hydraulic oil is added, it can prevent oil changes or blockage of system components. However, these additives will lose their effectiveness after a period of time.
The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.
total cost.The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation, and simple maintenance compared to the scissor fork type elevator.
The installation personnel should have the qualification for installing hydraulic cargo elevators,Zory Large hydraulic lifting platform, carefully implement the special construction plan for installation and construction, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.
technical service.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen,Zory Hydraulic automatic lifting platform, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Generally speaking, for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, the size and lifting type of the oil cylinder are increased, and in order to achieve the same effective area as the jacking force, the oil cylinder is added. If the latter is larger, a lifting mechanism should be selected.
There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
Zory .The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.
Optional configuration of fixed lifting platform: The fixed lifting platform can be equipped with auxiliary devices according to usage requirements, such as the safety protection device of the fixed lifting platform; Electrical methods; Form of work platform; Power form etc. The correct selection of various configurations maximizes the functionality of the lifting platform and achieves effective use.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.