ChekhanovLogis
ChekhanovSmall
ChekhanovHydraThe optional configurations of a fixed lifting platform include manual hydraulic power, movable flip plates that are easy to overlap with surrounding facilities, rolling or motorized roller tracks, safety contact bars to prevent foot rolling, organ type safety protective covers, manual or motorized rotating workbenches, hydraulic overturning workbenches, safety support rods to prevent the lifting platform from falling,ChekhanovLogistics hydraulic lifting platform, and universal ball countertops.
After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws and the hydraulic cargo elevator after reinforcement has robustness and safety.
Chekhanov.When working simultaneously at the upper and lower levels, a tight and firm protective partition, canopy or other isolation facilities must be erected in the middle of the boarding bridge, and workers must wear safety helmets.
Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.
.When using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work,ChekhanovElectric lifting platform Hydraulic lifting platform, and can only provide support for 1-2 people.
Usage and instructions for steel wire ropes in elevators: The steel wire ropes of the steel wire ropes require very high strength, usually made of high-quality carbon steel with a carbon content of 0.5% -0.8%. They are widely used as transmission components in elevators. Due to its large load-bearing capacity, light weight, smooth operation, suitable for high-speed transmission, high strength, strong overload capacity,ChekhanovFixed hydraulic lifting platform, and reliable operation, it has become a commonly used rope for hydraulic elevators.
Lines of various safety equipment
Where is good.Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.
The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits high-speed circuits, and speed switching circuits.
Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, replace it with a new valve.
Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.
Sincere service.Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
Clean the surface of the base and install anchor bolts. If the construction elevator is installed on the floor, use a pad iron under the base screws to increase the force surface between the nut and the floor, in order to reduce the impact of the nut on the floor; Insert steel plate gaskets of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite; After adjusting the verticality of the guide rail frame tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and press it tightly
The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
Chekhanov.After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.