BudaForklift loading and unloading platform boarding bridgeBeloved by many manufacturers

The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.

　　2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

Buda.Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success, you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, making them in a relaxed state; After the above preparations are completed, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.

Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.

.The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability.

Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.

Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage,Buda10 ton fixed boarding bridge, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products

Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.

The problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself, insufficient compression of the sealing ring, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found, Just replace it with a new one.

Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer,Buda10 ton mobile boarding bridge, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner

Click to view.Firstly, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition, whether the movement and working speed are stable, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, and do not overload or deviate. The rated load of the fixed hydraulic boarding bridge specified by the manufacturer is the total weight of the loaded goods and forklifts, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner

quality index.There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.

Once again, whether the site selection, pit design, and installation are in place, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.

Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T,BudaBoarding Bridge Container, large static load: 6T large width: 2M, large length: 4M. There are many classifications, generally divided into mobile boarding bridges and fixed boarding bridges. General: Solid tires with a length of 11M and a width of 1M. The Ramp loading and unloading platform is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.

Buda.Firstly, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition, whether the movement and working speed are stable, and whether the display is normal

Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T, large width: 2M, large length: 4M. There are many classifications, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.

Set up a new oil warehouse testing system: Before entering the hydraulic lifting channel, hydraulic oil should be stopped from sampling and testing. Unqualified oil should be stopped from entering the warehouse, and the quality of the warehouse should be strictly controlled. A special hydraulic oil protection system should be set up: the oil should be stored and stored according to the brand when entering the warehouse, and disorderly storage should be prohibited. It should be stored in a dry and ventilated place in the open air for daily rain and rain, and should not be close to the fire fixed hydraulic boarding bridge. Label storage system should be established for mixed types It is necessary to fill out labels in a timely manner and conduct regular sampling and testing: In order to ensure the quality of the oil products leaving the warehouse, it is necessary to conduct seven regular inspections of the hydraulic oil inventory. Any unqualified oil products found after testing should be disposed of in a timely manner and containers should not be used for regular cleaning. Containers containing hydraulic oil should be cleaned regularly, and special personnel should be assigned to handle some of the more precise parts in the fixed hydraulic boarding bridge. Although mechanical hydraulic drive is labor-saving and convenient, it is also complex and damaged. The primary reason for the fixed hydraulic boarding bridge is that its operating principle and structural characteristics are not clear, and its preventive maintenance is not very clear. The fixed boarding bridge is for convenient repair and maintenance. It will not affect the normal operation of the equipment.