JiningPlatform type boarding bridgeWhat

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

　　2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

Jining.The fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.

Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse,JiningFixed electric hydraulic boarding bridge, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working, fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.

.Set up a new oil warehouse testing system: Before entering the hydraulic lifting channel, hydraulic oil should be stopped from sampling and testing. Unqualified oil should be stopped from entering the warehouse, and disorderly storage should be prohibited. It should be stored in a dry and ventilated place in the open air for daily rain and rain, and should not be close to the fire fixed hydraulic boarding bridge. Label storage system should be established for mixed types, It is necessary to fill out labels in a timely manner and conduct regular sampling and testing: In order to ensure the quality of the oil products leaving the warehouse, it is necessary to conduct seven regular inspections of the hydraulic oil inventory. Any unqualified oil products found after testing should be disposed of in a timely manner and containers should not be used for regular cleaning. Containers containing hydraulic oil should be cleaned regularly, and special personnel should be assigned to handle some of the more precise parts in the fixed hydraulic boarding bridge. Although mechanical hydraulic drive is labor-saving and convenient, it is also complex and damaged. The primary reason for the fixed hydraulic boarding bridge is that its operating principle and structural characteristics are not clear, and its preventive maintenance is not very clear. The fixed boarding bridge is for convenient repair and maintenance. It will not affect the normal operation of the equipment.

The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.

The fixed hydraulic boarding bridge has three fundamental elements: purification, overheating, and air intake. There is a close internal connection between these three unfavorable factors, insufficient compression of the sealing ring such as oil cylinders. It may be due to poor quality of the sealing ring itself, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, only the damaged sealing ring needs to be found resulting in oil leakage. At this time, Just replace it with a new one.

The use of imported seals ensures excellent sealing performance of the hydraulic system.

quality.Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment, forklifts can directly enter the interior of the car compartment for batch loading and unloading operations. Only one person is required to operate without the need for power supply, speed up the flow of materials but also double the efficiency of loading and unloading operations, and obtain greater economic benefits.

High strength& quot; U& quot; The design of the shaped beam can ensure its high load and long-term operation without deformation.

The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.

Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation

Industry management.Firstly,JiningSimple forklift boarding bridge, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition, whether the movement and working speed are stable, and whether the display is normal

Once again, whether the site selection, pit design, and installation are in place, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.

There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.

Jining.Adopting imported integrated modular hydraulic station, with good sealing performance and long service life.

Product features: Fully hydraulic drive, easy to operate and reliable to operate.

The use of imported seals ensures excellent sealing performance of the hydraulic system.