HuairenMovable
HuairenContainLong term promotion to the axle factory, a 20 year old brand with competitive prices and guaranteed quality!
Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working, fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
Huairen. 3. Mobile loading and unloading bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. What should I do if the hydraulic cylinder of the boarding bridge leaks oil? The hydraulic cylinder is a relatively important component in hydraulic equipment, responsible for the lifting and lowering work of the equipment. When there is oil leakage in the hydraulic cylinder, everyone must take it seriously.
The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability.
.The fixed hydraulic boarding bridge has three fundamental elements: purification, overheating, and air intake. There is a close internal connection between these three unfavorable factors and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.
Afterwards, before the operation of the equipment (shè bè i), inspect the condition of the rotating grease (grease), check the condition of the rotating support gear (Gear), and immediately handle any abnormalities (ch ǔ l ǐ). Professional boarding bridge factory quality assurance, professional company,HuairenPlatform type hydraulic boarding bridge, timely supply, high cost-effectiveness, has become the preferred brand for many wire products, welcome to purchase!
The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, but also prevents the accumulation of grease, rainwater, and ice and snow. This equipment is particularly suitable for explosion-proof and flammable places, without generating sparks and no worries. The power can be configured as: manual hand pump power. Electric power. Ensure that the oil cylinder is processed by iron cutting and rolling. Several maintenance and upkeep items for the fixed boarding bridge: each rotating shaft pin should be maintained regularly to reduce wear and enhance flexibility in use; The use of hydraulic oil should follow the specified model, usually 46 # or 68 #, which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, and the market should clean the dust, sand, oil, iron blocks etc. on them. During maintenance, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding,HuairenFixed hydraulic loading and unloading boarding bridge, or looseness, and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, the boarding bridge manufacturer - editor will provide a detailed introduction (xiá ng xì)
The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.
Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.
Installation requirements.There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.
Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time,HuairenGround fixed boarding bridge, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.
Quality assurance.Long term promotion to the axle factory, a 20 year old brand with competitive prices and guaranteed quality!
When the boarding bridge is working (during loading), the manual switch is on. Precision diagnosis method, also known as objective diagnosis method, refers to the use of detection (inspection and testing) instruments and electronic computer systems to quantitatively analyze the hydraulic elements and hydraulic systems of the boarding bridge, in order to identify the fault location and cause. The green belt trimming machine mainly rotates the head, side and bottom films to complete the trimming of the top, side, and lawn of the green belt. The machine has a simple appearance, is very convenient to move, is easy to operate and can adjust the height freely. It can also trim the top, side, and lawn of the green belt at the same time, saving a lot of manpower. The hydraulic cargo elevator must be installed in a closed wellbore environment, and the actual situation of the wellbore determines the specifications and dimensions of the final hydraulic cargo elevator. This includes the width and depth of the shaft, as well as the conditions of the pit and machine room. A vehicle mounted hedge trimmer belongs to the technical scheme of garden machinery equipment, and the outer vertical arm can move up and down under the action of the lifting oil cylinder; Precision diagnostic methods include (b ā o kuò) Instrument testing methods, oil analysis methods, vibration acoustic methods, ultrasonic testing methods, and computer diagnostic expert systems.
Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
Huairen.Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation
The use of imported seals ensures excellent sealing performance of the hydraulic system.
A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.