GdanskMobile b
Gdansk ancientThe lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.
Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse,GdanskThe boarding bridge, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working, fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
Gdansk.At the beginning, it is essential to inspect and maintain the fixed hydraulic boarding bridge before or after use, and pay attention to whether it can be used correctly
Adopting anti slip patterned steel plates, the platform has good anti slip performance.
.Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation
Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation
Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.
The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions,GdanskMobile hydraulic lifting boarding bridge, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.
When using the boarding bridge for loading and unloading, load and unload according to the rated load, and do not be overweight. If overweight occurs, it will make the hydraulic system struggle during the lifting process, and even cause deformation of the hydraulic cylinder body, resulting in gaps and oil leakage outward. This requires finding a professional manufacturer for maintenance, such as Shanghai Niuli Machinery. If the deformation is severe, the only option is to replace it with a new one.
The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.
Statistics.Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, parallel to the cargo platform.
The boarding bridge is convenient for unloading, has strong stability, and low maintenance costs. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic, the boarding bridge is composed of mechanical systems, hydraulic systems, and electrical systems. Fully hydraulic drive, easy to operate and reliable to operate. The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability. The use of imported seals ensures excellent sealing performance of the hydraulic system. Adopting imported integrated modular hydraulic station, with good sealing performance and long service life. Monthly maintenance of the landing bridge of the lifting platform. The landing bridge, like other handling tools, sticky or has sand and gravel and other foreign matters it should be replaced in a timely manner; Each part should be filled with some oil separately, which can extend the service life of the bearing.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
High strength& quot; U& quot; The design of the shaped beam can ensure its high load and long-term operation without deformation.
Supply chain quality management.There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.
The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixed
The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.
Gdansk.Before delivery for use, it is necessary for us to conduct static and dynamic experiments on the fixed hydraulic boarding bridge equipment to achieve different application effects. Based on the equipment environment of the elevator and the application requirements of the fixed hydraulic boarding bridge itself, selecting appropriate equipment can achieve very good application effects. It is a specialized auxiliary equipment for completing the rapid loading and unloading of goods. The fixed hydraulic boarding bridge is used indoors or outdoors, and whether it is a fixed lifting channel or a mobile lifting channel. The fixed hydraulic boarding bridge helps to ensure the safe operation of our equipment. The countertop adopts a specially designed diamond grid plate with reliable strength, making the forklift have better climbing and maneuverability. Even in rainy and snowy weather, normal use can still be guaranteed.
Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then fix it on both sides of the carriage, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable,GdanskHydraulic fixed boarding axle, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products
3. Mobile boarding bridges are used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Only one person is required to operate without the need for power supply which can achieve safe and fast loading and unloading of goods.